Procom MN060HPA Owner'S Operation And Installation Manual Download Page 8

www.usaprocom.com

200048-01A

8

Use this work sheet to determine if you have 

a confined or unconfined space.

Space: 

Includes the room in which you will 

install heater plus any adjoining rooms with 

doorless  passageways  or  ventilation  grills 

between the rooms.
1.  Determine the volume of the space (length 

x width x height).

 

Length  x  Width  x  Height  =__________

 

cu. ft. (volume of space)

 

Example:

  Space  size  20  ft.  (6.1  m) 

(length)  x  16  ft.  (4.88  m)  (width)  x

 

8 ft. (2.44 m) (ceiling height) = 2560 cu. 

ft. (72.49 m

3

) (volume of space)

 

If additional ventilation to adjoining room 

is supplied with grills or openings, add the 

volume of these rooms to the total volume 

of the space.

2.  Multiply the space volume by 20 to deter-

mine the maximum Btu/Hr the space can 

support.

 

  ________(volume  of  space)  x  20  = 

(Maximum Btu/Hr the space can support)

 

Example:

 2560 cu. ft. (72.49 m

3

) (volume 

of space) x 20 = 51,200 (maximum Btu/

Hr the space can support)

3.  Add the Btu/Hr of all fuel burning appli-

ances in the space.

 

Vent-free heater 

 _________ Btu/Hr

 

Gas water heater*   _________ Btu/Hr

 

Gas furnace 

 _________ Btu/Hr

 

Vented gas heater   _________ Btu/Hr

 

Gas fireplace logs   _________ Btu/Hr

 

Other gas appl _______ Btu/Hr

 

Total 

= ________ Btu/Hr

 

*  Do  not  include  direct-vent  gas  appli-

ances.  Direct-vent  draws  combustion 

air  from  the  outdoors  and  vents  to  the 

outdoors.

AIR FOR COMBUSTION AND VENTILATION

 

30,000

  26,000

  56,000

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

 

Example:

 

 

Gas water heater   __________ Btu/Hr

 

Vent-free heater 

+ _________ Btu/Hr

 

Total 

= _________ Btu/Hr

4.  Compare the maximum Btu/Hr the space 

can support with the actual amount of Btu/

Hr used.

 

  _______Btu/Hr (maximum can support)

 

  _______Btu/Hr (actual amount used)

 

Example:

 51,200  Btu/Hr  (maximum  the 

space can support)

 

 

56,000 Btu/Hr (actual amount 

of Btu/Hr used)

The space in the above example is a confined 

space because the actual Btu/Hr used is more 

than the maximum Btu/Hr the space can sup-

port. You  must  provide  additional  fresh  air. 

Your options are as follows:
A.  Rework  worksheet,  adding  the  space 

of an adjoining room. If the extra space 

provides  an  unconfined  space,  remove 

door to adjoining room or add ventilation 

grills between rooms. See 

Ventilation Air 

From Inside Building, 

page 9

.

B.  Vent room directly to the outdoors. See 

Ventilation Air From Outdoors, 

page 9.

C.  Install a lower Btu/Hr heater, if lower Btu/

Hr size makes room unconfined. If the ac-

tual Btu/Hr used is less than the maximum 

Btu/Hr the space can support,

 

the space 

is an unconfined space. You will need no 

additional fresh air ventilation.

Summary of Contents for MN060HPA

































Reviews: