Proceq N / L Operating Instructions Manual Download Page 18

16 

Maintenance 

© 2017 Proceq SA

•  Turn knurled screw (33) to rewind the recording paper 

from reel (31) to reel (32).

•  Pull out the knurled screw (33) until it locks and then 

remove the reel (32).

•  Insert a new roll with the text "Value 100" on the side 

closest to the knurled screw (33).

•  If the knurled screw (33) does not engage, turn the reel 

(32) until the knurled screw (33) starts turning with it as 
well.

•  Cut off the start of the paper strip like an arrow and 

insert it into the slot in reel (31).

•  Tension the paper by turning the reel (31).

3 .4 Storage

Prior to the storage of the hammer in the original case 
release the impact as during a measurement and fix the 
plunger (1) with the push-button (6). Secure the push-
button additionally with a strong adhesive tape.

3 .5  Maintenance Procedure

We recommend that the concrete test hammer should
be checked for wear after 2 years at most and be  
cleaned. Do this as described below.

 

The concrete test hammer can either be sent  

  to a service center authorized by the vendor or 

 

else it can be maintained by the operator  

 

according to the following description.

The items (in brackets) are illustrated in Fig. 3.3, 
"Lengthways section through the concrete test hammer" 
on page 18.

3 .5 .1  Stripping Down

 Warning!

 

Never strip down, adjust or clean the pointer  

 

and pointer rod (4) (see Fig. 3.3, page 18),  

 

otherwise the pointer friction may change.

 

Special tools would be required to readjust it.

•  Position the concrete test hammer perpendicular to the 

surface.

 Danger!

 

The impact plunger (1) generates a recoil  

 

when it deploys. Therefore always hold the  

 

concrete test hammer with both hands!  

 

Always direct the impact plunger (1)  

 

against a hard surface!

•  Deploy the impact plunger (1) by pushing the concrete 

test hammer towards the surface until the pushbutton 
(6) springs out.

•  Unscrew the cap (9) and remove the two-part ring (10).
•  Unscrew the cover (11) and remove the compression 

spring (12).

•  Press the pawl (13) and pull the system vertically up 

and out of the housing (3).

Summary of Contents for N / L























Reviews: