background image

3

Pursuant to this Limited Warranty, Horizon 
Hobby, Inc. will, at its option, (i) repair or (ii) 
replace, any product determined by Horizon 
Hobby, Inc. to be defective. 

In the event of a 

defect, these are your exclusive remedies.

This warranty does not cover cosmetic damage or 
damage due to acts of God, accident, misuse, abuse, 
negligence, commercial use, or modification of or 
to any part of the Product. This warranty does 
not cover damage due to improper installation, 
operation, maintenance, or attempted repair by 
anyone other than an authorized Horizon Hobby, 
Inc. service center. This warranty is limited to the 
original purchaser and is not transferable. In no 
case shall Horizon Hobby’s liability exceed the 
original cost of the purchased product and will 
not cover consequential, incidental or collateral 
damage. Horizon Hobby, Inc. reserves the right 
to inspect any and all equipment involved in a 
warranty claim. Repair or replacement decisions 
are at the sole discretion of Horizon Hobby, Inc. 
Further, Horizon Hobby reserves the right to 
change or modify this warranty without notice.

REPAIR OR REPLACEMENT AS PROVIDED 
UNDER THIS WARRANTY IS THE EXCLUSIVE 
REMEDY OF THE CONSUMER. HORIZON 
HOBBY, INC. SHALL NOT BE LIABLE FOR ANY 
INCIDENTAL OR CONSEQUENTIAL DAMAGES.

As Horizon Hobby, Inc. has no control over 
use, setup, final assembly, modification 
or misuse, no liability shall be assumed 
nor accepted for any resulting damage or 
injury. By the act of use, setup or assembly, 
the user accepts all resulting liability.

If you as the purchaser or user are 
not prepared to accept the liability 
associated with the use of this product, 
you are advised to return this product 
immediately in new and unused 
condition to the place of purchase.

Safety Precautions

This is a sophisticated hobby product and not 
a toy. It must be operated with caution and 
common sense and requires some basic mechanical 
ability. Failure to operate this product in a safe 
and responsible manner could result in injury 
or damage to the product or other property. 

This product is not intended for use by 
children without direct adult supervision.

The product manual contains instructions 
for safety, operation and maintenance. 
It is essential to read and follow all the 
instructions and warnings in the manual, 
prior to assembly, setup or use, in order to 
operate correctly and avoid damage or injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase 
cannot provide warranty support or repair. 
Once assembly, setup or use of the product 
has been started, you must contact Horizon 
Hobby, Inc. directly. This will enable Horizon to 
better answer your questions and service you in 
the event that you may need any assistance.

Questions or Assistance

For questions or assistance, please direct 
your email to productsupport@horizon
hobby.com, or call 877.504.0233 toll free 
to speak to a service technician.

Inspection or Repairs

If your product needs to be inspected or repaired, 
please call for a Return Merchandise Authorization 
(RMA). Pack the product securely using a shipping 
carton. Please note that original boxes may be 
included, but are not designed to withstand the 
rigors of shipping without additional protection. Ship 

Limited Warranty & Limits of Liability

Summary of Contents for Miss Elam Plus

















Reviews: