pro-gard.com
800.480.6680
2
THESE COMPONENTS ARE REQUIRED
TO INSTALL THE PRO-GARD MOTORCYCLE GUN RACK SYSTEM
I.
Removing contents saddle bag
A. Remove all items from the right-side saddle bag of the motorcycle.
II.
Removing Saddle bag fasteners
A. Remove the OEM fasteners from the saddle bag brackets located at the top inside the saddle bag.
Replace the retaining fasteners located on saddle bag mounting bracket with the retaining fasteners
(94850A158) provided in the hardware kit.
NOTE: Leave rubber bushings installed.
III. Installing the gun rack
A. Orient the gun rack so the that the barrel of the gun is facing toward the rear of the saddle bag. Align
the mounting holes in the gun rack frame with the OEM holes in the saddle bag. Using the supplied
nuts, bolt, and washers attach the gunrack and saddle bag using the OEM mounting points.
B. Secure all fasteners
IV.
Wiring the Gun Lock
A. Mount the release button (momentary switch) in a concealed location that can be reached easily by
the officer, while holding on to the weapon.
B. Connect the red lead of the gun lock to one side of the release button (momentary switch) and the
green wire from the timer. It will be necessary to add appropriate gauge.
C.
Connect a wire lead from the other side of the release button (momentary switch) to the red wire
from the timer and either a switched or un-switched power source on the fuse block. This will allow
the lock to operate with the ignition key on, or off, respectively.
D.
Connect a wire lead from the other side of the release button (momentary switch) to the red wire
from the timer and either a switched or un-switched power source on the fuse block. This will allow
the lock to operate with the ignition key on, or off, respectively.
MOTO - GUN RACK SYSTEM
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
MAIN FRAME
3G1806
1
1
MAGAZINE BRACKET
3G1807
1
2
CHARGING BRACKET
3G1803
1
3
BARREL FOAM BRACKET
3G560
1
4
BARREL FOAM
3G586
1
5
R GUN LOCK
G4904-NPG
1
6
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
5/16 SLIP CLIP
94850A158
2
7
5/16-18 x 1" HHMS, Zn (NOT SHOWN)
3X75
2
8
1/4-20 X 3/4 PHIL TRUSS HD MS
3X05
2
9
1/4-20 WHIZ NUT (NOT SHOWN)
3X16
4
10
1/4-20 X 5/8 PHIL TRUSS HD MS
3X03
2
11
5/16-18 X 1-1/4 BSHCS, BK
3X197
2
12
1
1
2
2
A
A
B
B
Products, LLC
7988 Centerpoint Dr., Suite 400
Indianapolis, IN 46256
(317) 579-6680
PART DESCRIPTION:
DRAWN BY:
SCALE:
CHECKED BY:
DATE:
APPROVED:
UNLESS OTHERWISE SPECIFIED :
The information contained herein is
proprietary and the property of Pro-gard
Products and may not be reproduced,
disclosed or used for any other purpose other
than a quotation to or an order from
Pro-Gard Products without the specific
written authorization of Pro-gard Products.
Computer Path:
SIZE:
A
ENGR 1:
ENGR 3:
ENGR 2:
FINAL:
PRODUCTION:
Third
Angle
Projection
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMALS:
.005
DIMENSIONS ARE IN INCHESTOL ON ANGLES
1°
TOL ON 2 PLACE DECIMAL
.015
NOTE:
MATERIAL:
FINISH:
STAMP:
ASSEMBLY NO:
DRAWING NO:
SHEET:
REV:
APPL:
Pro
-
gard
1 OF 6
REVISION HISTORY
REV
SHEET
DESCRIPTION
AUTHOR
DATE
00
ALL
NEW RELEASE
EICHHORN
1/28/2015