background image

12

13.

Make sure that all parts are properly tightened before you use the treadmill.

If there are sheets of clear

plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-

mill. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt (see

pages 26 and 27).

12. Attach the Latch Housing (71) to the Left Upright

(73) with two #10 x 1" Tek Screws (76).

Make

sure that the large hole in the Latch Housing

is on the side shown. Do not overtighten the

Latch Screws.

Locate the Latch Pin (72). Remove the knob

from the Latch Pin. Make sure that the collar

and the spring are on the Latch Pin. Then, insert

the Latch Pin into the Latch Housing (71), and

tighten the knob back onto the Latch Pin.

76

Spring

Knob

71

12

73

72

Collar

Large

Hole

If you purchase the optional chest pulse sensor (see page 22), follow the steps below to install the re-

ceiver included with the chest pulse sensor.

1.

Make sure that the power cord is unplugged.

Remove the indicated M4.2 x 16mm Screw (12)

and the Access Door (97) from the Console

Base (88).

2. Connect the wire on the receiver to the indi-

cated wire extending from the Console Base

(88).

Hold the receiver so the antenna is ori-

ented as shown and is facing the Console

Base.

Attach the receiver to the plastic posts on

the Access Door (97) with the two included

small screws.

3.

Make sure that no wires are pinched.

Reattach the Access Door (97) with the M4.2 x

16mm Screw (12). Discard the other wires in-

cluded with the receiver.

Receiver

97

Antenna

12

88

Wires

Small

Screws

Summary of Contents for 30864.1





































Reviews: