background image

13

HOW TO USE THE ELLIPTICAL

HOW TO FOLD AND UNFOLD THE ELLIPTICAL

When the elliptical is not in use, the frame can be

folded out of the way. First, lift the latch under each

pedal arm, and lift the pedal arms off the adjustment

sleeves on the crank arms.

Next, raise the pedal arms until they touch the mag-

nets on the upper body legs; the magnets will hold the

pedal arms in place. Then, hold the handle and lift the

frame until it locks in a vertical position.

To use the elliptical, first hold the handle, press the

latch button, and lower the frame.

Next, pull the pedal arms off the magnets on the upper

body legs. Then,

lift the latches under the pedal

arms,

and set the pedal arms on the adjustment

sleeves on the crank arms. Release the latches, and

make sure that the pedal arms are securely connected

to the adjustment sleeves.

HOW TO MOVE THE ELLIPTICAL

To move the elliptical, first fold it as described at the

left. Next, stand in front of the elliptical, hold the

upright, and place one foot against one of the wheels.

Pull the upright until the elliptical rolls on the front

wheels. Carefully move the elliptical to the desired

position, and then lower it to the floor.

HOW TO ADJUST THE STRIDE LENGTH OF THE

ELLIPTICAL

To adjust the stride length of the elliptical, first pull one

of the adjustment knobs until the adjustment arm will

pivot freely. Pivot the adjustment arm until the adjust-

ment knob is aligned with one of the holes in the crank

arm, and gently release the knob into the hole.

Pivot the adjustment arm back and forth slightly to

make sure that the adjustment pin is engaged in one

of the holes in the crank arm.

Adjust the stride length on the other side of the ellipti-

cal in the same way.

Make sure that both sides of

the elliptical are adjusted to the same stride

length.

Handle

Magnet

Latch Button

Sleeve

Crank

Arm

Latch

Pedal Arm

Adjustment

Arm

Adjustment

Knob

Crank

Arm

Holes

Adjustment

Pin

Summary of Contents for 10.0 Ze Elliptical





























Reviews: