PRO Charging System i1215BSBDUAL Safety, Installation And Operating Instructions Download Page 7

 
On single bank systems, simply try the charger on another battery.  If the charger now operates normally 
(steady red LEDs or changes to green and holds), this indicates a possible problem with the original 
battery. 
 
If the same bank continues to malfunction, please call our technical support group (800.742.2740). 
 

PROBLEM: A green LED was illuminated before disconnecting the power from the charger, but 
upon reconnection, red LEDs appear and remain on. 

 
Solution Sequence:  This is normal operating procedure for the system and simply indicates that a re-
analysis of the battery status has been initiated and after a series of steps, the green LED will illuminate. 
 

PROBLEM: Two red LED indicators flashing. 

 
Solution Sequence:  This indicates a Forming Stage timeout and alerts the user that the battery voltage 
has not risen above an acceptable limit within 3 hours.  Battery should be tested. 
 

PROBLEM: Three red LED indicators flashing. 

 
Solution Sequence: 

 

This indicates that the charger has exceeded the maximum amount of time allowed 

for charging the battery.  Battery should be tested.

 

 

PROBLEM: Four red LED indicators flashing. 

 
Solution Sequence:  This indicates that the internal temperature of the charger has exceeded allowable 
limits and this bank of the charger has shut down.  If charger is in a closed compartment, open 
compartment doors and allow charger to cool for 8 hours.  After this period, connect the charger to AC 
and begin charging again. 

 

LIMITED WARRANTY 

 
Pro Charging Systems, LLC (PCS) makes this Limited Warranty only to the original retail purchaser.   
PCS warrants this battery charger for three years (unless the charger is used in a Restricted Market) from 
the date of retail purchase against defective materials and/or workmanship.  Restricted markets include 
markets outside of the USA, Rental applications and Heavy Industrial applications.  Sometimes RM is 
designated in the PCS Part number when ordered, but is not part of the model number.  Chargers used in 
Restricted Markets will have a warranty period of 18 months from the date of retail purchase against 
defective materials and/or workmanship.  CR refers to “Certified Reconditioned” and designates a 1 year 
warranty.    If such defects should occur, this unit will either be repaired or replaced at the discretion of 
the manufacturer.  It is the responsibility of the original purchaser to return the charger along with proof of 
purchase, transportation, and/or any mailing or handling charges prepaid to the manufacturer or its 
authorized representative.  Chargers that are purchased more than two years beyond the date of 
production will automatically have a warranty start date that will be the two year anniversary of the 
production date. 
 
This limited warranty is void if the product is misused, improperly maintained, handled carelessly or 
incorrectly operated.  Additionally, this warranty is void if the charger is disassembled, the charger’s 
charge cables are cut, the power cord is cut off, the charger is altered without authorization from PCS, the 
serial number is removed, or repair is attempted by anyone other than an authorized representative.  PCS 
makes no other warranty other than this limited warranty and expressly excludes any implied warranty, 
including warranty for any incidental or consequential damages.  This is the only expressed limited three 
year warranty authorized by PCS and does not authorize anyone to assume or make any other obligation 
towards the product other than this three year Limited Warranty.  Some states do not allow limitation of 
incidental or consequential damages. 
 
This warranty gives you specific legal rights and you may also have other rights which vary from state to 
state.  Please call Pro Charging Systems, LLC for full warranty information and/or service please call 
(800.742.2740).   
 

 

Summary of Contents for i1215BSBDUAL









Reviews: