background image

22

Congratulations on the purchase of your Pro Boat™ Vortex 46 Airboat. You are just minutes from one of 
the most thrilling experiences that the radio control hobby has to offer.

The Pro Boat Vortex 46 is a professionally built, ready-to-run fiberglass Airboat model. Powered by the 
potent Evolution 46 engine, you will be able to race across the water and enjoy the unique thrill of airboat 
performance.

Read this owner’s manual thoroughly. You also need to read the included Evolution 46 engine manual, along 
with the Pro Boat radio system manual.

It is very important that you operate this boat responsibly. With proper care and maintenance, you will be 
able to enjoy your Vortex 46 for many years to come.

Carefully unpack Vortex 46 and examine the boat and its contents. The box should contain the Vortex 46 
RTR with radio installed, a boat stand, and the Pro Boat radio transmitter. If you are missing any of these 
items or notice any damage, immediately contact the place of purchase.

This boat is not a toy! It is a high performance RC model boat. Do Not take risks that could endanger you 
or others.

Before operating your model, make sure your frequency is clear. If someone else is operating on the same 
frequency, both models could go out of control, possibly causing damage to the models, as well as to others.

Be certain to check all of the hardware, exhaust system, and propeller, making sure that all are secure 
before and after each run. Always stay clear of the propeller when the engine is running!

When you first begin to run your Vortex 46, place in water with the engine running at approximately 1/8 
throttle. Slowly increase the throttle until boat accelerates onto plane. Gradually increase throttle to no 
more than 1/2 until you become more familiar with the boat. 

When operating this model, stay clear of people, full-sized boats, stationary objects, and wildlife. Also, watch 
out for fishing lines that could get tangled in the propeller and rudder. It is preferable to operate the  
Pro Boat Vortex 46 only in calm water. We also suggest that you do not run the Vortex 46 in salt water. 
If at any time while operating your Vortex 46 you sense any abnormal function, end your operation 
immediately. Do not operate your Vortex 46 again until you are certain the problem has been corrected.

Service Center Information

If you have any questions regarding the Pro Boat Vortex 46, please contact the Horizon Service Center:

Horizon Service Center

4105 Fieldstone Rd.

Champaign, IL 61822

1-877-504-0233

Introduction

Warning

Summary of Contents for Vortex 46 Airboat

















Reviews: