background image

A Picture to 

Remember

Setup Instructions

INSTALLATION INSTRUCTIONS

Carefully 

remove and unwrap all the 

contents of box. Referring to the parts 
list, make sure you have everything 
needed to proceed with the installation 
of the lens. If any parts are missing, 
contact Prismasonic immediately.

Inspect the lens to make sure there are 
no shipping defects. If you notice a 
problem with the lens itself, or the lens’ 
mechanical system, contact Prismasonic 
immediately.

Parts list:

„

Lens Unit

„

Shipping Rail (2 pcs)

„

Stand Plate 

„

Stand Rail (4 pcs)

„

Stand Rail Extenders (4 pcs)

„

Slide Lock (4 pcs)

„

L-Wrench 2, mm

„

L-Wrench 3, mm

„

L-Wrench 4, mm

„

L-Wrench 5, mm

„

Black Cap (2 pcs)

„

Skt Cap Screw, M6 x 10 (6 pcs)

„

Instruction Manual

Anamorphic Lens

HD-6000M

Bringing the lens into the use:

Flip the 

lens unit 

with 

shipping rails

 upside 

down on a table.

 

By using the 

L-wrench, 5 mm

 

carefully remove the delivery lock screws of 
large lens from the bottom plate 

(Fig 1-a)

. After 

this release the two upper screws of front 
element 

(Fig 1-b)

 by using the

 L-wrench, 3mm

STEP 2 

Remove the bottom plate 

(Fig 2)

 of housing by 

releasing the four screws on the bottom plate 

(Fig 1-c)

. Now carefully take off the plastic cover 

coats from both sides of both lenses

Remove 

also the cover coats from both IR windows of 
motor box.

Fig 1

 

b)

b)

c)

a)

c)

c)

c)

a)

Fig 2

 

Fig 3

c)

c)

a)

b)

a)

a)

a)

b)

STEP 3 

Insert the bottom plate back to the housing and 
prepare to affix the four screws

 (Fig 3-a

) with 

L-

wrench 3mm. 

Tighten the screws securely.

 

Also 

insert the 

black caps

 into the slot of bottom plate 

(Fig 3-b). 

Now also attach the two cap screws of front plate 
back to their places 

(Fig 3-c)

.

Anamorphic Lens

HD-6000M

Summary of Contents for HD-6000M

Page 1: ...6000M Bringing the lens into the use Flip the lens unit with shipping rails upside down on a table By using the L wrench 5 mm carefully remove the delivery lock screws of large lens from the bottom plate Fig 1 a After this release the two upper screws of front element Fig 1 b by using the L wrench 3mm STEP 2 Remove the bottom plate Fig 2 of housing by releasing the four screws on the bottom plate ...

Page 2: ...tend the travel use the rail extenders of main rails Fig 5 The set of extension rails increases the slide travel for 4 5 cm The each extension rail is screwed securely into the main rail after which it is working as a single longer stand rail Fig 5 STEP 6 Now very carefully set the lens unit onto the stand plate with stand rails exactly as presented in Fig 6 so that 12 mm Ø rails go through the li...

Page 3: ... in focus simultaneously Fig 9 Fig 12 Anamorphic Lens HD 6000M Setup Instructions Anamorphic Lens HD 6000M Fig 11 STEP 11 For the presentation of native 16 9 material carefully lift the lens up above the upper pair of slide locks Adjust the height of lock pair until the lens has completely moved aside from the beam Fig 11 and again make sure the locks are in a same level with each other The slide ...

Page 4: ... driven up and is in contact with the spring plate of slide Save the shipping rails and use them in case of re shipment of the lens You re done Enjoy your new 2 40 1 picture Maintenance Your Prismasonic lens was designed to require very minimal cleaning It is best to only wipe the lens housing with a clean damp soft cloth when needed Cleaning the optics Only use optically safe lens cleaning soluti...

Reviews: