background image

537-512revD-EN                                                                                                                            Printed in USA 2/06 © 2006

2

TOASTER

TX-230BKCE

Product Identification

Electrical Specifications

Installation

Model No.

Volts

Watts Amps

Hz

TX-230BKCE

230

5000

21.7

50

Safety Information

Remove the unit from the carton and inspect for signs of damage. If
there is damage to the unit:
•  notify the carrier within 24 hours of delivery
•  save carton and packaging materials for inspection purposes
•  contact your local dealer, or if purchased directly, the Prince Castle 

Sales Department at 800-722-7853 or 1-630-462-8800 to arrange for a
replacement unit.

Verify that all parts have been received (see 

Components

, page 2). 

Plug the power cord into the proper electrical receptacle. All electrical
connections must be in accordance with local electrical codes and any
other applicable codes.

Important

Prince Castle reserves the right to change specifications and product design without notice.  Such

revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements

for previously purchased equipment.

WARNING

Indicates information important to the proper opera-
tion of the unit. Failure to observe may result in dam-
age to the equipment and/or severe bodily injury or
death.

CAUTION

Indicates information important to the operation of
the unit. Failure to observe may result in damage to
the equipment.

Side Cover and

Thumbscrews

Lower Retaining Bar

Upper Retaining Bar

Teflon Release Sheet

Conveyor Belt

(under cover)

Power On/Off

Button

Front

Cover

Bun Ramp

Components

Summary of Contents for TX-230BKCE











Reviews: