background image

Horizontal Infrared Toaster 

IRT-SB-NA-1PS 
IRT-SB-NA-3PS 

IRT-SB-NA-1PS 

2

6

IRT-SB-NA-3PS 

Remove Power Cord 

 Unplug the unit 

WARNING 

Failure to disconnect power 
from the unit before servicing 
could result in severe bodily 
injury or death. The ON/OFF 
Switch does not disconnect 
incoming power to the unit.

Using a Phillips head screwdriver, open the right side 
panel. Reference the 

Red Arrow

Remove (3) connections from power cord by removing 

the three screws shown, Reference the 

Blue Arrow.

 

Reinstall the power cord onto the unit. Tighten the 
strain relief bushing. Previously removed in step 4. 

Reinstall the (3) connections from the power cord on 

the points shown. Previously removed in step 3. 

Using a Phillips head screwdriver, reinstall the right 
side panel. Previously removed in step 2. 

# 2 

# 3 

# 3 

# 3 

# 4 

Unscrew the back of the strain relief bushing to      
release the power cord.  Remove the power cord from 
the unit completely. Refer to the 

Green Arrow

Re

place

 Power Cord 

Plug in unit. Power on and ensure the unit is fully 
functional. 

Printed in USA 

12

/

3

/2020

353

-

56

7

 Rev. 

B

Summary of Contents for IRT-SB-NA-1PS































Reviews: