background image

UPRIGHT (1)

CABLE SUPPORTS (2)

Distributed by Primal Vantage Company Inc. 685 Route 10 East, Randolph, NJ 07869

Customer Service Department 1-866-972-6168

www.primalparts.com

• 

ALWAYS

 thoroughly inspect the tree before installing your product. 

DO NOT

 install your TREE/LADDER STAND onto any dead or unsafe tree, telephone 

or utility pole, structural column, or man-made structure. Doing so may result in serious injury or death.

• 

ALWAYS

  select the proper tree for use with your TREE/LADDER STAND. Select a live straight tree that fits within size limits recommended (minimum 

tree diameter must be no less than 9 inches and maximum of 18 inches.). 

DO NOT

 rely on a  branch for support.

• 

DO NOT

 select a tree in the dark or choose a tree in close proximity to a fence. You must not have any stumps or rocks beneath your tree.

• 

NEVER

 use TREE/LADDER STAND on a tree that is dead, diseased , leaning or on wet and uneven ground as the tree may fall, break or uproot.

• Your tree must not be wet, icy or slippery or on wet, swampy, or loose ground that allows the tree to be unstable. Check the ground under TREE/LADDER STAND 

to ensure it is firm and level.

• Be sure you have a level stand platform. Your tree must not lean or have any irregular shape.

• Tree must not have any loose or scaly bark or excessive vines, nails, screws, or any other sharp objects protruding that may sever webbing on product. 

Any surrounding trees must not lean or have dead limbs that may fall onto you or your product.

• 

NEVER HURRY!!

 While climbing a TREE/LADDER STAND, make slow, even movements no more that ten to twelve inches at a time. Make sure you have 

proper contact with tree and/or TREE/LADDER STAND every time you move. 

On ladder tree stand, ALWAYS maintain three points of contact with each 

step 

and 

ALWAYS

 

lean forward as you climb

.

C H O O S I N G   A   S A F E   T R E E

CAUTION:

CAUTION:

Maximum Tested Weight Capacity Limit for this Product is: 

300 POUNDS

(Including Accessories, Gear and Attire)   

DO NOT Exceed tested weight limit capacity.

This product is designed for only ONE PERSON. 

TREE STRAP

(1)

SEAT CUSHION (1)

RIGHT & LEFT 

TREE CONTACTS (2)

WRENCH (2)

PLATFORM (1)

SEAT FRAME (1)

(1)

M8 x 110mm HEX BOLT

(2  Washers, 1 Lock-Nut)

(1)

M8 x 100mm HEX BOLT

(4  Washers, 1 Lock-Nut)

(2)

M8 x 55mm HEX BOLT

(4  Washers, 1 Lock-Nut)

(2)

M8 x 55mm HEX BOLT

(3  Washers, 1 Lock-Nut)

STRAP BRACKETS

(2)

(2)

M8 x 45mm HEX BOLT

(3  Washers, 1 Lock-Nut)

PROPER CARE AND MAINTENANCE:

• Inspect for defects (damage, rot, corrosion, cracks, freezing, excessive heat, etc.) before every use is required. Do not use if damage is detected or 

suspected.

• Ameristep recommends periodically re-tightening and/or replacing hardware (supplied by Ameristep), including bolts, nuts, washers, rope, straps, 

cord, etc.  

©2012 (rev. 11/11)

Summary of Contents for THE CHALLENGER 51004/9201










Reviews: