Pride Mobility Quantum 6000Z series Owner'S Manual Download Page 40

40

www.pridemobility.com

Quantum 6000Z

A P P E N D I X   I   -   S P E C I F I C A T I O N S

Suspension: 

Active-Trac ATX with integrated rear dual-strut suspension and articulating caster beam

Drive Wheels: 

35.56 cm (14 in.), pneumatic or solid available

Caster Wheels: 

15.24 cm (6 in.) solid

Maximum Speed:¹

Up to  9.66 km/h (6 mph)

  

Up to 12.87 km/h (8 mph ) (with high-speed motor option)

Brakes: “Intelligent 

Braking” 

electronic regenerative, disc park brake

Ground Clearance:² 

See figure 29.

Maximum Safe Slope: 

8.7% (5°)

Turning Radius:² 

See figure 29.

Overall Size:² 

Length: See figure 29.

 

Width: See figure 29.

Drivetrain: 

Two motor,  Mid-wheel-6 drive

Batteries:³ 

Two 12-volt, deep-cycle, NF-22/Group 24 batteries

 (standard)

   

Two 12-volt, NF-22 required with Power Elevating Seat

Range:¹

,

4

 

Up to 20.3 km (13 miles)

Battery Charger: 

Off-board 

Weight Capacity: 

136 kg (300 lbs.)

  

113.4 kg (250 lbs.) with TRU-Balance Pediatric Power Tilt

  

72.57 kg (160 lbs.) with Synergy Manual Tilt

Component Weights: 

Base: 66.68 kg (147 lbs.)

  

Batteries: NF-22 batteries 17.24 kg each (38 lbs.); Group 24 batteries 24.04 kg (53 lbs.)

SPECIFICATIONS

1

Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition,

motors, controller type, tyre type, and tyre condition. This specification can be subject to variance of (+ or -) 10%.

²

Due to manufacturing tolerances and continued product improvement, this specification can be subject to variance of

(+ or – ) 3%.

³ 

AGM or Gel-Cell type required. See VI. “Batteries and Charging.”

4

Tested in accordance with ASNI/RESNA, WC Vol 2, Section 4 & ISO 7176-4 standards. Results derived from theoret-
ical calculations based on battery specifications and drive system performance. Test conducted at maximum weight 
capacity.

NOTE: The product conforms to all applicable ANSI-RESNA testing requirements and ISO 7176 series EN12184 
standards. All specifications subject to change without notice.

Summary of Contents for Quantum 6000Z series












































Reviews: