background image

10

TSS300

Weight Limitations

Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.

Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories

mounted to the power chair.

MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the

weight capacity voids your warranty. Pride will not be held responsible for injuries and/or

property damage resulting from failure to observe weight limitations.

WARNING! Do not carry passengers on your power chair. Carrying passengers on your power

chair may affect the center of gravity, resulting in a tip or a fall.

Tire Inflation

If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly.

Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.

WARNING! It is important that the psi/bar/kPa air pressure rating indicated on the tire be maintained

in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure may result

in loss of control, and overinflated tires may burst. Failure to maintain the psi/bar/kPa air pressure

rating indicated on the pneumatic tires at all times may result in tire and/or wheel failure.

WARNING! Inflate your power chair drive tires from a regulated air source with an available

pressure gauge. Inflating your tires from an unregulated air source could overinflate them,

resulting in a burst tire.

NOTE: If the tire on your power chair lists the psi rating only, use the following conversion formulas to find

the bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.

Incline Information

More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.

Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on

your power chair.

„

Proceed with extreme caution as you approach the downgrade of a ramp or other incline.

„

Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power

chair’s rear wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any

railing corners.

„

When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure

a safely controlled descent.

„

Avoid sudden stops and starts.

When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then

accelerate cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive

in the forward direction only. If your power chair starts to move down the incline faster than you anticipated or

desired, allow it to come to a complete stop by releasing the joystick, then push the joystick forward slightly to

ensure a safely controlled descent.

WARNING! When on any sort of an incline or decline, never place the power chair in

freewheel mode while seated on it or standing next to it.

WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of

the incline. Drive your power chair straight up the incline. This greatly reduces the

possibility of a tip or a fall. Always exercise extreme caution when negotiating an

incline.

WARNING! You should not travel up or down a potentially hazardous incline (i.e.,

areas covered with snow, ice, cut grass, or wet leaves).

WARNING! Never travel down an incline backward. Doing so may cause the power

chair to tip. Always exercise caution when negotiating an incline.

I I .   S A F E T Y

Summary of Contents for Jazzy select elite













































Reviews: