2
BEFORE FIRST USE
1. Become familiar with the MyJo
™
coffee maker parts (Fig. A) and read the following
information.
2. Unscrew the base from the reservoir. Then pull out the pump from the reservoir and
remove all contents from inside the reservoir.
3. Wash the coffee maker parts in warm, soapy water. Rinse thoroughly to remove any
soap residue.
Do not wash the MyJo
™
coffee maker in the dishwasher.
Caution!
There is a sharp needle in the pack holder which is designed to puncture
the single serve pack. To prevent injury, do not place fingers in the pack holder.
HOw TO USE
To prepare coffee or tea, follow the instructions below.
(To prepare hot cocoa and other beverages, refer to the instructions on page 3 before
beginning.)
The amount of water used with your MyJo
™
coffee maker will determine the strength
of your coffee or tea. For the first use, fill the water reservoir to the fill lines suggested
below:
• For normal strength coffee or tea, fill to the 8-ounce line with water.
• For stronger coffee or tea, fill to the 6-ounce line with water.
• For weaker coffee or tea, fill to the 10-ounce line with water.
For subsequent uses, adjust the strength, if necessary, by simply increasing or decreasing the amount of water as desired.
NOTE:
The fill line markings provide the necessary water to produce 6, 8, and 10 ounces of brewed coffee or tea.
1. Place a single serve pack into the pack holder (Fig. B).
Press down firmly on the single serve pack un-
til the bottom of the pack is punctured.
Caution!
There is a sharp needle in the pack holder. To prevent
injury, do not place fingers in the pack holder.
2. Heat the water and assemble the unit using one of the following methods:
A. Microwave
:
• Fill the water reservoir with the desired amount of water.
• Place the filled reservoir in the microwave.
Be sure the base is not attached to the reservoir, as the
base is not microwave safe.
Heat the water to the desired temperature.
Caution!
When handling the reservoir containing hot
water, always grasp the red grip as the other portions of the reservoir will be very hot.
• Push the pump cap onto the top of the pump.
• Attach the pump to the reservoir. Insert the ridged portion of the pump into the reservoir, pressing around the pump edge until
the pump is attached firmly to the reservoir.
IMPORTANT:
Press only the pump edge. Do
not
press the pump cap or pump.
• Grasp the red grip on the filled reservoir and place the reservoir onto the base. Screw on clockwise until tight.
B. Tea Kettle
:
• Use an electric or stovetop tea kettle and heat water to the desired temperature.
• Attach the base to the reservoir prior to filling it with water. Screw the reservoir on clockwise until tight. Then, place the unit
on a dry, level surface and carefully fill the reservoir with the desired amount of heated water.
Caution!
Do not hold onto the
reservoir when pouring hot water into it.
• Push the pump cap onto the top of the pump.
• Attach the pump to the reservoir. Insert the ridged portion of the pump into the reservoir, pressing around the pump edge until
the pump is attached firmly to the reservoir.
IMPORTANT:
Press only the pump edge. Do
not
press the pump cap or pump.
3. Brew
• The MyJo
™
coffee maker is designed to fit on most coffee mugs. Verify that your mug is the right size before pumping your coffee.
The ribs on the bottom of the base should fit within the inside rim of your mug. The diameter of the inner rim of the mug should be
at least 2¼˝ but not more than 3¾˝ wide. You should also make sure you select a mug which is the appropriate size for the amount
of coffee or tea you are brewing.
Pump cap
Pump
water
fill lines
water
reservoir
Base
Fig. A
Reservoir
grip
Pack holder
Ridged
portion
Base ribs
Pump edge
Fig. B
Pack
holder