Prestige Platinum APS-590TWC Owner'S Manual Download Page 4

128-6819

4 of 12

Toggling Between Vibrate, Chirp, or Both Chirp & Vibrate:
The two way transmitter offers the option of having Beep Tones, Vibration, or
Both Beep Tones & Vibration associated with the function responses of the
transmitter.
To toggle between these modes, press simultaneously the "F" function button
and the Unlock Icon Button.  The transmitter will beep, beep & vibrate, or vibrate
only toggeling on the specific preference.

Check Vehicle Status:
Press the lock+key+option buttons of either transmitter simulta-
neously for 1 second.  The vehicle's alarm will display the
systems current status, on the two way transmitter, breifly by
flashing the LED associated with the state that the vehicle is in.
This feature is useful if you do not want to wait the 10 seconds
for a LED to display the status or if you just want to check the
status without operating the Lock or Unlock buttons.

 ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle and close all doors, hood lid
and trunk lid.
2. Press and release the Lock button on the keychain transmitter.

þ

 Dash mounted LED begins to flash slowly.

þ

 Parking Lights flash one time.

þ

 Siren sounds one chirp.

If the siren/horn

 

sounds 3 chirps, then you have left a door, trunk,

or hood lid ajar. Simply close the opened entry point to provide full

protection.  If the siren "chirped" three times, sometime after arming, the exclusive
delayed dome light learn circuit has been programmed and the system detected
a open entry point after the learned delay expired.  Again, closing the hood, trunk,
or doors will correct the problem and you do not need to disarm the system to
make the correction.  If the siren/horn did not sound when arming, then the chirps
have been turned off and you should refer to the section titled "ELIMINATING THE
ARM/DISARM CHIRPS" in this manual.

o

 Doors Lock - Optional

o

 Headlight Illumination - Optional

SILENT ARMING - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

þ

 Dash mounted LED begins to flash slowly.

þ

 Parking Lights flash one time.

þ

 Siren will not sound.

If the siren "chirped" three times, sometime after arming, the exclusive
delayed dome light learn circuit has been programmed and the system
detected a open entry point after the learned delay expired.  Closing the

4

Summary of Contents for Platinum APS-590TWC













Reviews: