128-9322
7/8
Page 7
Programmable Features :
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st Door L/UL
.8 Sec.
3.5 Sec.
.8 S L, Dbl.U/L
.8 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
Off
3rd Accy. UL
Auto UL Dr
Auto UL Off
Off
4th Passive Locks
Passive
Active
Active
5th Passive/Active Arm
Passive Arm
Active Arm
Active Arm
CAUTION:
Setting the sensitivity too high can cause false alarms due to noise vibrations from passing trucks and
heavy equipment. To decrease sensitivity, turn the adjustment screw counter clockwise.
Wire Dressing:
Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape. Secure these looms along
the routing using cable ties. This will ensure that the alarm wires are not damaged by falling onto hot or sharp moving
surfaces in the vehicle.
Operation:
Take a few moments to check off the appropriate option boxes in the owner’s manual and to fully explain the operation
of the system to your customer
.
PROGRAMMING BANK 1
(TRANSMITTERS):
Transmitter Model Name, 143BP Is Also Found On Back Of
Transmitter Case (Battery Use CR2032)
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times (Siren Chirps)
3) Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren.
4) Press the valet/program button to advance to the unlock channel two, (siren chirps)
5) Press the Unlock button of each transmitter you want to operate the unlock function until you hear a chirp from the
horn or siren.
6) Press the valet/program button to advance to the trunk release channel three, (siren chirps).
7) Press the trunk button of each transmitter you want to operate the trunk release feature until you hear a chirp from
the horn or siren.
8) Turn the ignition switch off.
The above action programs the Lock, Unlock, & optional Trunk Release,
This remote has the ability to operate 2 similar alarms from a single transmitter. To toggle on and off vehicle one or two:
Press the Trunk/Key the Lock button for 5 seconds.
The LED flashes 2 times. Release the buttons, to select 2nd vehicle mode.Program this transmitter into the second
vehicle's system. Any time you are in 2nd vehicle when the transmitter is operated, the LED will flash twice for each
function. When in in the prime vehicle mode, the LED will flash once for each function.
PROGRAMMING BANK 2
(ALARM FEATURES):
You can enter bank 2 from bank 1 by turning the ignition key off then on from step 4 of Bank 1.
(Siren Short then Long Chirp), or You can also go right to bank 2 by:
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times (Siren Chirps).
3) Turn the ignition key off then on. (Siren Short Then long Chirp)
4) Press the pushbutton switch once to advance to feature 1, twice to advance to feature 2, etc, then use the lock button
of the transmitter to select the feature setting.
Example to set passive arming:
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times (Siren Chirps).
3) Turn the ignition key off then on. (Siren Short Then long Chirp)
4) Press the pushbutton switch 5 times to advance to feature 5, Passive/Active Arm, then use the lock button of the
transmitter to select two chirps "Active Arm".
5) To exit the programming mode, turn the ignition key off. The program mode is automatically exited when there is no
activity on the pushbutton switch or the transmitter lock button.
