Presby Environmental EnviroFin Design And Installation Manual Download Page 22

2.0 SYSTEM DESIGN 

© Presby Environmental, Inc., Design & Installation Manual, July 2020 Edition  

22 

 

 

Illustration of by-pass venting: 

Vent Manifolds 

A vent manifold may be incorporated to connect the ends of a number of sections 

or rows of EF units to a single vent opening. Slope the lines connecting the 

manifold to the FDU to drain condensation.  

 

2.7  Aquaworx Remediator 

The Aquaworx Remediator system provides aerobic conditions to significantly reduce wastewater strength and 

increase the dissolved oxygen concentration in the effluent.  The bacteria within the oxygen-rich wastewater 

works to minimize the waste materials suspended in the effluent. The Remediator is installed in the last chamber 

of a state approved multi-compartment septic tank per manufacturer requirements. Note: All minimum septic tank 

sizing requirements listed in Env-Wq 1010 must be met independent of, and without respect to, use of a 

Remediator. Illustrated below is the option of installing a Remediator in the outlet chamber of a 1,500-gallon 

Infiltrator IM-1530 plastic tank configured for multi-compartment use: 

Summary of Contents for EnviroFin































Reviews: