background image

 
 

Dear Customer, 
 
Thank you for your purchase of a 

Two-Rock

 amplifier from Premier 

Builders Guild.  
 
 
As a discerning guitarist, you know the road to great tone begins with 
great components. 
 
Our Classic Design, carefully selected parts and hand-built approach 
combine to make an extremely versatile instrument. 
 
Please take the time to read this manual.  We hope it will answer any 
questions that you may have. 
 

We extend a warm welcome to you as a member of a select group of 
musicians who have chosen a 

Two-Rock

 amplifier.

 

 

 
 

Important Safety Instructions

 

1. Read these instructions 
2. Keep these instructions 
3. Heed all warnings 
4. Follow all instructions 
5. Do not use this apparatus near water 
6. Clean only with dry cloth 
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions 
8. Do not install near any heat sources such as radiators, heat registers, plugs, and the point 
where they exit from the apparatus 
9. Protect the power cord from being walked on or pinched particularly at plugs and the point 
where they exit from the apparatus 
10. Only use attachments/accessories specified by the manufacturer 
11. Unplug this apparatus during lightning storms or when unused for long periods of time 
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has 
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, 
does not operate normally, or has been dropped 
13. CAUTION: To disconnect the unit completely from the MAINS, unplug the unit. Turning the 
power switch off does not disconnect the unit completely from the MAINS. 
 

Summary of Contents for Two-Rock Coral 100











Reviews: