Prem-Air PREMSW Manual Download Page 3

1.

GENERAL INFORMATION

1.1

INTRODUCTION

PLEASE NOTE.
Do not dispose of any packaging until the installation of the equipment is completed.

(See list of accessories).

1.2

BS PLUG WIRING

Wiring Instructions: Should it be necessary to change the plug please note the wires in the mains
lead are coloured in accordance with the following code :

BLUE - NEUTRAL

BROWN - LIVE

GREEN AND YELLOW - EARTH

BLUE

NEUTRAL

N

BLACK

BROWN

LIVE

L

RED.

GREEN/YELLOW

EARTH

E

GREEN OR GREEN/YELLOW

13A (BS 1363)

13A

Wiring for a 13 Amp Plug (BS1363)

E

After having removed the packing, check that all the content is intact and complete.

In the event of missing parts, contact your retailer.

This unit has been designed to cool or heat the air of a room and should only be used for this purpose.

The manufacturer cannot be held liable for damage caused to property or injury to persons or animals due to
incorrect installation, regulation and maintenance or improper use.

This air-conditioner contains R410-A refrigerant: at the end of its life, the disposal of this equipment must be
in accordance with the strict regulation governing the recycling of this product, please operate with caution
during the disposal.
Please contact your local authority for regulatory advice.

Do not switch on before having totally assembled the unit and before installing in its correct operating
position.

Before starting the appliance, check that it is correctly earthed, according to the legislation in force in the
country concerned.

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:

1. The

wire is the

and must be connected to the terminal which is marked with the letter

or coloured

.

2. The

wire is the

and must be connected to the terminal which is marked with the letter

or

coloured

3. The

is the

and must be connected to the terminal which is marked with the

letter

or

or coloured

.

4. Always ensure that the cord grip is positioned and fastened correctly.

If a

fused plug is used it must be fitted with a

fuse.

If in doubt consult a qualified electrician.

Please note.
The Earth Terminal is marked with the letter

or Earth Symbol

.

Earth-

(Green/Yellow)

Neutral - N

(Blue)

Live - L

(Brown)

13
AMP

3

Summary of Contents for PREMSW

















Reviews: