PREFORMED Coyote HiCount Manual Download Page 12

12

18.00 SAFETY CONSIDERATIONS

18.01

This application procedure is not intended to supersede any company construction or safety
standards.  This procedure is offered only to illustrate safe application for the individual.
CAUTION: FAILURE TO FOLLOW THESE PROCEDURES AND RESTRICTIONS MAY RESULT
IN PERSONAL INJURY OR DEATH.

18.02

This product is intended for the specified application.  CAUTION: DO NOT MODIFY THIS
PRODUCT UNDER ANY CIRCUMSTANCES.

18.03

This product is intended for use by trained craftspeople only.  This product SHOULD NOT BE
USED by anyone who is not familiar with and trained in the use of it.

18.04

When working in the area of energized lines with this product, EXTRA CARE should be taken to
prevent accidental electrical contact.

18.05

For PROPER PERFORMANCE AND PERSONAL SAFETY be sure to select the proper size
PREFORMED™ products before application.

18.06

PREFORMED™ products are precision devices.  To insure proper performance, they should be
stored in cartons under cover and handled carefully.

SP2924

P.O. Box 91129, Cleveland, Ohio 44101 • 440.461.5200 • www.preformed.com • e-mail: [email protected]

Summary of Contents for Coyote HiCount













Reviews: