Precor StretchTrainer Assembling And Maintaining Manual Download Page 19 | Manualshive

Page: 19 / 28

background image

Assembling the StretchTrainer

17

2.

Fully tighten all seat bracket bolts.

Important:

Do not overtighten the bolts. Doing so may

compress or crack the plastic alignment bracket.

3.

Remove the paper backing from the adhesive tape on the

placard mount.

Figure 13: Adhesive tape removal

4.

Carefully center the instructional placard on the placard

mount and press firmly into place.

Figure 14: Placard attachment

5.

To attach the rear level adjusters, raise the rear end of the

StretchTrainer slightly off the floor. Slide a rubber level

adjuster onto one side of the rear base rail.

«
...
17
18
19
20
21
...
»

Summary of Contents for StretchTrainer





























Reviews:

No comments

Related manuals for StretchTrainer

ACS880-01 Series

Brand: ABB Pages: 238

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: NEC Pages: 44

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Federal Pages: 43

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Naked Pages: 36

Brand: R&S Pages: 2677

GED5000IL Series

Brand: Zimmer Pages: 52

Brand: Yacht Devices Pages: 32

NTP TECHNOLOGY DAD Thunder Core 256

Brand: DAN Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands