background image

©2019 Precor Inc. | Glute Extension RSL 618 | Assembly Guide

11

Image

Hardware

Instructions

1

Snap the lower pulley shroud        onto the lower front shroud       . Place 
the lower front shroud with pulley cover into frame and hook on to but-

tons.

2

1        M6 x 15 mm SHCS
Tool: Hex wrench, 4 mm

Secure lower pulley shroud.

3

Place the lower rear shroud        onto the frame. Raise it enough to hook 
over buttons. 

4

Install the rear middle shroud       . Slide it over the triangular tabs of the 
lower shroud and hook it onto middle buttons.

Repeat for the front middle shrouds       .

5

Install the upper rear        and front shrouds       . Ensure to hook them 

over the buttons and spacers.  

6

2        M10 x 40 mm SHCS
Tools: Hex wrench, 8 mm
Torque wrench

Place shroud crown        on top and secure. 

Recommended bolt torque 

is 25 ft-lb (34 N-m).

7

Securely snap top tray        into place.

8

19

Install the Shroud

20

39

25

19

24

20

21

22

38

23

9

8

21

22

23

24

25

9

38

39

IMPORTANT

Before installing the shroud, ensure that cable connections are correct and cables move smooth through their paths. If they do not, 

STOP

 and adjust cable and routing. In addition, ensure all fasteners (including those preinstalled) are tightened appropriately.

     

 Note 

 The location of the lower pulley cover will vary depending on the model.

Summary of Contents for Resolute RSL 618













Reviews: