Precision Medical EASY PULSE PM4150 SERIES Service Manual Download Page 5

3 | 

P a g e

 

 

Warnings and Cautions  

  

WARNING  

Oxygen supplied from this device is for supplemental use and is not intended to be life supporting or life sustaining.   
This device is not intended for use by patients who would suffer immediate, permanent, or serious health consequences 
as a result of an interruption in the oxygen supply.  
  

 

This device is NOT to be used by patients who breathe through their mouths.  

 

DO NOT smoke in an area where oxygen is being administered.  

 

DO NOT use near any type of flame or flammable/explosive substances, vapors or atmosphere.  

 

DO NOT use oils, greases, lubricants or any combustible materials on or near this product. Wash hands properly 
prior to usage.  

  

TO AVOID INCREASED RISK OF FIRE  

 

Keep oxygen equipment away from open flames. Use and store the POC at least five (5) feet away from 
equipment such as furnaces, water heaters, and stoves that may contain open flames.  

 

Keep equipment in a well-ventilated area at all times.  

 

High concentrations of oxygen can cause rapid burning of other substances.  

 

DO NOT place blankets, draperies, or other fabrics over equipment.  

 

DO NOT use if dirt or contaminants are present on or around fill connectors on the POC.  

 

NO OXYGEN is delivered when the Pulse Selector is at the “Off” Setting.  

 

NO OXYGEN is delivered in between settings.  

 

DO NOT use while sleeping without consulting your Equipment provider.  

 

CAUTION  

 

This device is designed to operate with a single lumen, adult, nasal cannula with a maximum length  of 7 feet or 
less.  

 

Only individuals instructed and trained in its use should operate this device. 

 

Inspiratory efforts vary from patient to patient. The POC may not be able to detect respiratory efforts of all 
patients.  

 

This device contains magnetic, ferrous material that may affect the results of an MRI.  

 

DO NOT use liquid leak detector to test for leaks.  

 

DO NOT autoclave.  

 

DO NOT gas sterilize.  

 

DO NOT clean with aromatic hydrocarbons.  

 

DO NOT immerse device in any kind of liquid.  

 

Avoid dropping the device or placing it in a position where it could fall and become damaged.  

 

DO NOT block the outlet fitting or kink the cannula tubing when the device is in use.  

 

Store device in a clean area when not in use.  

 

Only use the Precision Medical carrying bag or carrying bag/backpack that is supplied from Precision Medical with 
the POC.   

 
 

Summary of Contents for EASY PULSE PM4150 SERIES





















Reviews: