Precision matthews CS-315V, Manual

Page: 15 / 27

9.3 Loa
•
Use
•
Mea
•
Plac
•
Slide
•
Pres
•
Use
If repetit
•
Use
betw
•
The
Decreas
The cla
size.
Please
decreas
1. chec
2.
9.4 Set
Setting t
single le
The stop
•
Cut
•
Unc
•
Slide
•
Clam
•
The
9.5 Ope
E
B
ading the W
the vise han
asure and ma
ce the work-p
e the work-p
ss the work-p
the vise han
tive cuts are
the vise han
ween the mo
n use the vis
se vibration
mping vise
be followed
sing the vibr
k the workp
tting Cuttin
the cutting le
ength.
p bar in use
off the first le
clamp the wo
e the work-p
mp the work-
n proceed w
eration Cyc
Work-piece
nd-wheel to o
ark off the len
piece on the f
iece across t
piece up aga
nd-wheel to c
required for m
nd-wheel to a
bile vise jaw
se lock lever
n (workpiece
can be adju
d the trick as
ration.
piece’s cente
g Length
ngth remove
ength of work
rk-piece
iece forward
-piece.
ith the opera
cle
A B C
H
C
A
D
open the vise
ngth of mater
flat surface in
the vise so th
inst the back
clamp the wo
material of th
approach the
and the work
to clamp and
e position se
usted forwa
s below whe
er not over
es the need to
•
Meas
off.
•
Load
•
Line
•
Clam
•
Loos
•
Slide
stop
•
Tight
k-piece.
until it reach
ation cycle
•
Set t
•
Open
•
Load
•
Clam
•
Adjus
•
Chec
•
Set t
(H).
15
e wider than t
rial desired t
n between th
hat the length
k vise jaw.
ork-piece.
he same widt
e work-piece,
k-piece.
d unclamp th
etting)
ard and back
en loading
the center o
o repeatedly
sure and ma
d the work-pie
up the cut
mp the work-p
sen the hex n
e the bar rise
bar (B) touch
ten the hex n
hes tip of the
the miter cut
n the vise, if
d the work-pie
mp the work-p
st the bar sto
ck that the m
the speed (C
the width of t
o be cut-off.
he vise jaws.
h mark lines
th:
, but leave an
e work-piece
kward to cla
(setting) the
of blade. Ple
y measure wo
ark off the len
ece.
piece.
nut at the bas
r (A) along th
hes the end
nut at the bas
stop bar (A)
angle, if nec
necessary
ece
piece
op for cutting
ain power lig
), read the sp
the work-piec
up with the b
n approximat
e.
amp work-p
e work-piece
ease see dr
ork-pieces fo
gth of mater
se of the bar
he long rod (C
of the work-p
se of the bar
.
essary
length, if ne
ght is ON (A)
peed display
ce.
blade or disk
te 5mm gap
piece for var
e position fo
rew A
or repetitive c
rial desired to
riser (A).
C) so that th
piece.
riser (A).
ecessary
).
yed on the wi
.
rious
or
cuts of a
o be cut-
e tip of
ndow