Precision Digital Corporation PD6100-6H0 Instruction Manual Download Page 19

Page: 19 / 47

™ PD6100 Strain Gauge, Load Cell, and mV Meter

Instruction Manual

Setup and Programming

There is

no need to recalibrate

the meter

when first received from the factory.
The meter is

factory calibrated

prior to

shipment for millivolts with calibration
equipment that is certified to NIST standards.

Overview

There is a 5-position DIP switch to set the meter input
selection. See

Switch Configuration

on page

setup the switch.
Setup and programming is done through the front
panel buttons.
After power and input signal connections have been
completed and verified, apply power to the meter.

Front Panel Buttons and Status
LED Indicators

Button

Symbol

Description

LED

Status

Menu

1-8

Alarm 1-8
indicator

Right
arrow/F1
Zero meter

1-8

Flashing:
Relay in
manual
control mode

Up arrow/F2
Reset tare

Flashing:
Tare

Enter/F3
Tare

Gross

Note:

F4 is a digital input. Alarms
5-8 are enabled when relay
expansion module is
installed.

1-8

Flashing:
Relay
interlock
switch open

Note:

LEDs for relays in
manual mode flash
with the “M” LED every
10 seconds. “M”
flashing by itself
indicates Aout

–

manual control is used.

•

Press the Menu button to enter or exit the
Programming Mode at any time.

•

Press the Right arrow button to move to the next
digit during digit or decimal point programming.

•

Press or hold the Up arrow button to scroll
through the menus, decimal point, or to
increment the value of a digit.

•

Press the Enter button to access a menu or to
accept a setting.

•

Press and hold the Menu button for three
seconds to access the advanced features of the
meter.

Summary of Contents for PD6100-6H0
















































Search results

Summary of Contents for PD6100-6H0

Reviews:

Related manuals for PD6100-6H0

Brands by name

Popular brands

Precision Digital Corporation PD6100-6H0, Instruction Manual

Search results

Summary of Contents for PD6100-6H0

Reviews:

Related manuals for PD6100-6H0

Brands by name

Popular brands