Precision Digital Corporation PD6100-6H0 Instruction Manual Download Page 4

Page: 4 / 47

™ PD6100 Strain Gauge, Load Cell, and mV Meter

Instruction Manual

Relay Sampling Operation .......................................................................... 30

Relay Operation Details ................................................................................ 31

Overview ..................................................................................................... 31

Relays Auto Initialization ............................................................................. 31

Fail-Safe Operation ..................................................................................... 31

Front Panel LEDs ........................................................................................ 31

Latching and Non-Latching Relay Operation .............................................. 31

Non-Latching Relay (

Auto

) ......................................................................... 32

Non-Latching Relay with Manual Reset (

A-nman

) ....................................... 32

Latching Relay (

LatcH

) ............................................................................... 32

Latching Relay with Clear (

Lt-Clr

) ............................................................ 32

Acknowledging Relays ................................................................................ 33

Pump Alternation Control Applications (

Altern

) ........................................ 33

Setting Up the Interlock Relay (Force On) Feature ..................................... 34

Scaling the 4-20 mA Analog Output (

Aout

) ................................................. 35

Setting Up the Password (

pass

) ................................................................... 35

Protecting or Locking the Meter .................................................................. 35

Making Changes to a Password Protected Meter ....................................... 35

Disabling Password Protection.................................................................... 35

Reset Menu (

reset

) ....................................................................................... 35

Tare Menu (

Tare

) ........................................................................................... 36

Tare Functionality (

tare

) ............................................................................ 36

Manual Control Menu (

Contrl

) ..................................................................... 36

Advanced Features Menu ............................................................................. 36

Advanced Features Menu & Display Messages.......................................... 36

Noise Filter (

filter

) ................................................................................... 37

Noise Filter Bypass (

bypass

) ...................................................................... 37

Rounding Feature (

round

) .......................................................................... 37

Modbus RTU Serial Communications (

serial

) .......................................... 38

Select Menu (

SElect

) ................................................................................. 38

Input Signal Conditioning (

Functn

) ............................................................. 38

Auto-Zero (

Auto 0

) ..................................................................................... 39

Low-Value Cutoff (

CutofF

) ......................................................................... 39

Analog Output Programming (

AoutPr

) ....................................................... 39

Programmable Function Keys User Menu (

user

) ....................................... 40

Internal Source Calibration (

ICAL

) .............................................................. 41

Error Message (

error

) ............................................................................... 41

Meter Operation ................................................................................................. 42

Front Panel Buttons Operation .................................................................... 42

Function Keys Operation .............................................................................. 42

F4 Operation .................................................................................................. 42

Maximum/Minimum Readings ...................................................................... 42

Troubleshooting................................................................................................. 43

Diagnostics Menu (

diag

) .............................................................................. 43

Determining Software Version..................................................................... 43

Reset Meter to Factory Defaults ................................................................... 43

Factory Defaults & User Settings ................................................................ 44

Troubleshooting Tips .................................................................................... 45

EU Declaration of Conformity ........................................................................... 46

Summary of Contents for PD6100-6H0
















































Search results

Summary of Contents for PD6100-6H0

Reviews:

Related manuals for PD6100-6H0

Brands by name

Popular brands

Precision Digital Corporation PD6100-6H0, Instruction Manual

Search results

Summary of Contents for PD6100-6H0

Reviews:

Related manuals for PD6100-6H0

Brands by name

Popular brands