PreCise 002-00177, Manual

Page: 13 / 36

13
CAUTION: Do not use or operate your Precise
SHP without a sleeve or tip attached to the
handpiece.
CAUTION: Handpiece sleeves and whitening
cones are supplied in a non-sterile condition.
These items must be sterilized prior to each use,
then subsequently handled and used in a sterile
environment. See Section 4.1.3 for instructions
on sterilizing the handpiece sleeve and Section
4.1.5 for the whitening cone.
Disposable tips are single-use. See Section
4.1.4 for instructions on cleaning and use of
these articles. DO NOT autoclave.
3.2.2. Power on Precise SHP
Slide a single-use display barrier sleeve over the Control
Pod.
Press the power button on the front of Base Unit. The power
button will illuminate, indicating that the Base Unit is
receiving power.
Press the power button on the Control Pod. Touch the screen
on the Control Pod and select the Precise SHP App. The
screen will now display the Introduction Screen.
3.2.3. Introduction Screen
When this screen appears, simply
touch anywhere on the screen to
advance to the password screen.
3.2.4. Passcode Screen
You will be required to enter a
4-digit passcode in order to access
the laser functions. After entering the
passcode, hit Enter. The installation
guide that is included in the kit
contains the factory-set passcode
for your unit. It is recommended
that you change the passcode
after first accessing the system (see
Section 3.2.9). If the passcode
does not work, or if you have
forgotten your code, please contact
the CAO Customer Care group
(1.877.236.4408) as described in
Section 6.2 to receive an override
passcode that will allow you to regain access to the system.
You must have the serial number and manufacture date
of the Base Module available when contacting the Service
Center.
3.2.5. Main Menu
From this screen, you can access
different portions of the laser
settings and information relative to
the system:
Operate – This takes you to the laser
performance settings and allows you to
activate the Precise SHP handpiece.
Presets – This section contains a number
of presets listed by procedure. The most
commonly performed procedures are listed.
Selecting one of these procedures will auto-
populate the Operate screen with the ideal
laser settings for the selected procedure.
Utilities – This section allows
you to adjust some features of
the laser, change the password,
synchronize the display with the base,
and find production information on your
particular system.
Product Key Screen
Password Screen
Main Menu Screen
oper
a
ting
1. Remove the handpiece protective dust cap. (Figure 3.1)
2. Slide the handpiece sleeve over the fiber cable stem and
rotate it to securely thread the sleeve onto the fiber cable
stem. (Figure 3.2a)
3. Remove the protective cap from the shaft of the disposable
tip, and insert the tip shaft into the end of the handpiece.
You will know that the tip is securely seated when you feel
the tip snap into place and hear a slight click. (Figure 3.2b)
4. Slide the disposable barrier sleeve over the handpiece
assembly. If needed, puncture the barrier sleeve with the tip
so the tip fiber protrudes out of the barrier sleeve.
5. Your Precise SHP handpiece is ready to use
Assembly of the therapy handpiece is done by attaching the
therapy handpiece sleeve in the same manner as the surgical
sleeve as described in Step 3.2 above. No other attachments or
steps are needed for the therapy handpiece assembly.
Assembly of the whitening handpiece is accomplished by
attaching the reusable dispersion cone to the whitening sleeve
by aligning the locking pins in the cone with the groves in the
sleeve, then pressing and rotating the cone. The cone is now
secured to the sleeve. Attach the whitening sleeve to the fiber
cable stem as described in Step 2 above. See Figures 3.3a and
b.
Figure 3.2a. Attach sleeve.
Figure 3.2b. Attach disposable tip.
Figure 3.1. Remove dust cap.
Figure 3.3a. Line up tabs with notches when attaching the cone
Figure 3.3b. Whitening sleeve ready for attachment to the
fiber stem.