background image

COMPATIBILITY

MOTHERBOARD 

MITX, mATX, ATX, eATX

OPTICAL DRIVES

 

Up to two 5.25” drives, can support 

dual 5.25” bay reservoir

STORAGE DRIVES

 

4 HDD or 4 SSD 

3 HDD and 1 SSD 

2 HDD and 2 SSD 

1 HDD and 3 SSD 
SSDs up to 2.5” and HDDs up to 

3.5” are supported

An additional 2 drives can be 

mounted through the optional 

HDD/SDD tray. Tray is sold 

separately. 

PSU

 

ATX PSUs up to 300mm supported

SWITCHES

 

Up to 4x 16mm Vandal Switches

RESERVOIRS

 

Full Primochill line up is supported

*

120MM CTR reservoirs are 

supported without additional 

mouting kits. Larger reservoirs 

require an additional mounting kit 

that can be found on primochill.

com. Standard mounting patterns 

are provided for non-Primochill 

brand reservoirs. 

RADIATOR | BACK BRACKET

INTERNALLY 

120MM - 240MM 

140MM - 280MM

EXTERNALLY

 

120MM - 480MM 

140MM - 560MM

No thickness limit

Up to 4 radiators can be mounted 

via additional brackets. 

RADIATOR | BOTTOM BRACKET  

240MM - 280MM 

40MM thickness limit when using 

other bracket add-ons. No thickness 

limit otherwise.

RADIATOR | AiO/SIDE BRACKET

AiO

 

All-in-One units with 13” tubes have 

been tested. 

Up to two AiO units supported via 

additional bracket.

RADIATORS 

120MM - 480MM 

140MM - 560MM

40mm radiator thickness limit is 

recommended due to weight. Up 

to two radiators are supported via 

additional brackets.

Summary of Contents for WETBENCHSX Series


















Reviews: