manualshive.com logo in svg

Pratissoli MW Series, Repair Manual, Page: 12 / 54

Share
Download
Pratissoli MW Series Repair Manual Download Page 12

                                                          

MW

  

12 

 
 
 
In the event that it is necessary to replace one or more con-rods or piston guides, operate as follows: 
Unscrew the screws with tool code 27566200 to unlock the con-rods (pos.

c

, fig.32) and then extract the 

con-rod-piston guide units from the back casing opening (pos.

c

, fig.33). 

 

   

 

 
 
It is now possible to disassemble the piston guide seal rings, taking care to not damage the piston guide 
sliding rod. 
 
 

              Whenever it becomes necessary to replace the piston guide seal rings without   
              dismantling the entire mechanical part, it is possible to extract the seal rings with the use of  
              tool code 27918500 operating as follows:  

 
 
Insert the tool between the rod and the seal ring (pos.

c

, fig.34) and, with the extractor hammer, complete 

insertion of the tapered section inside the seal ring (pos.

c

, fig.35) 

 

   

 

 
 
 
 
 
 
 
 
 
 

1 

fig. 32 

fig. 33

1 

fig. 34 

1 

fig. 35

1 

Summary of Contents for MW Series























































Reviews:

No comments