background image

 

 

INVERTER GENERATOR – P2000i 

 

SAFETY INFORMATION 

 

FUEL IS HIGHLY FLAMMABLE AND POISONOUS 

  Always turn off the engine when refueling. 

  Never refuel while smoking or in the vicinity of an open flame. 

  Take care not to spill any fuel on the engine or muffler when refueling. 

  If you swallow any fuel, inhale fuel vapor, or allow 

  Any to get in your eye(s), see your doctor immediately. If any fuel spills 

on  your  skin  or  clothing,  immediately  wash  with  soap  and  water  and 

change your clothes. 

  When operating or transporting the machine, be sure it is kept upright. If 

it tilts, fuel may leak from the carburetor or fuel tank. 

 

EXHAUST FUMES ARE POISONOUS 

  Never  operate  the  engine  in  a  closed  area  or  it  may  cause 

unconsciousness and death within a short time. Operate the engine in a 

well ventilated area. 

 

 

ENGINE AND MUFFLER MAY BE HOT 

 

  Place the machine in a place where pedestrians or children are not likely 

to touch the machine. 

 

 

  Avoid  placing  any  flammable  materials  near  the  exhaust  outlet  during 

operation. 

 

 

 

 

 

Summary of Contents for P2000i










































Reviews: