MANUAL
GCP TX BUTTONS 2
P30351 - 07/2022
Rev. 0
LINE
Made by:
Motoppar da Amazônia Indústria e Comércio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro
Santa Rita do Sapucaí - MG - CEP 37.540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.citrox.com.br | +55 14 3407 1000
WARNING:
Do not use the equipment
without referring to this
manual rst.
Features
- Electronic circuit produced with SMD components;
- 2 independent command buttons;
- Reinforced xing strap;
- Fixed code;
- Buttons attached to the body;
- Frequency 433.92 Mhz;
- It is used to activate alarm centers and door and gate operators.
NOTE: The TX leaves the factory with the rolling code, to change the TX code to
xed, press and hold the 'A' and 'P' buttons at the same time until the LED turns off
(about 10 seconds), the code will be set xed, to recon gure TX to rolling code,
just do the same procedure.
In Rolling code, the LED blinks when any button is pressed and in xed code the
LED lights up
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR da Amazônia Indústria e Comércio de Eletrônicos Ltda, registered with CNPJ No.
09.084.119/0002-45, located at Praça Linear, No. 100, Bloco II, Centro, Santa Rita do
Sapucaí/MG, CEP 37.500-000, manufacturer of the PPA and CITROX products, guarantees
this device against defects in design, manufacture, assembly and/or jointly and severally as
a result of defects in the quality of the material that make it inappropriate or unsuitable for
the consumption for which it is intended, for a legal period of 90 (ninety) days from the date
of purchase, provided that the installation guidelines described in the instruction manual
are observed.
As a result of the credibility and trust placed in PPA AND CITROX products, we added
another 275 days to the above period, reaching a total of 1 (one) year, also counted from the
date of purchase to be proven by the consumer through the proof of purchase (Supervisor
Note).
In the event of a defect, within the warranty period, the liability of PPA and/or CITROX is
restricted to the repair or replacement of the device manufactured by it, under the
following conditions:
1.
The repair and readjustment of the equipment can only be carried out by the
Technical Assistance, which is quali ed to open, remove, replace parts or
components, as well as repair the defects covered by the warranty, and, in the
absence of this and any use of parts not originals contained in the use, will result in
the waiver of this term by the consumer;
2.
The warranty will not extend to accessories such as cables, screws kit, xing brackets,
sources, etc.;
3.
Expenses for packaging, transport and reinstallation of the product are exclusively
borne by the consumer;
4.
The equipment must be sent directly to the company responsible for the sale,
representative of the manufacturer, through the address on the purchase invoice,
properly packaged, thus avoiding the loss of warranty;
5.
The replacement or repair of the equipment does not extend the warranty period.
This warranty will be void if the product:
1.
Suffer damages caused by agents of nature, such as atmospheric discharges, oods,
res, landslides, etc.;
2.
It is installed in an improper electrical network or even in disagreement with any of
the installation instructions set out in the manual;
3.
Defects caused by falls, blows or any other physical accident;
4.
For violation of the equipment or attempt to repair by unauthorized personnel;
5.
It is not used for its intended purpose;
6.
Not used under normal conditions;
7.
Suffer damage caused by accessories or equipment attached to the product.
Recommendation:
We recommend the installation and maintenance of the product by a specialized technical
service.
If the product has a defect or abnormal operation, look for a specialized Technical Service for
the necessary corrections.
