PowerTec 40Hp Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 68

background image

53

6.When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

7.Insert and tighten the gear oil drain
screw.

Cleaning fuel tank

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

If you have any question about properly
doing this procedure, consult your
PowertecOutBoards dealer.

Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.

Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.

Wipe up any spilled fuel immediately.

Reassemble the fuel tank carefully. Im-
proper assembly can result in a fuel
leak, which could result in a fire or ex-
plosion hazard.

Dispose of old gasoline according to lo-
cal regulations.

1. Gear oil drain screw
2. Oil level plug

NOTE:
If the magnetic gear oil drain screw
equipped: remove all metal particles from

4.Remove the oil level plug to allow the oil
to drain completely.

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a PowertecOutBoards dealer
for repair of the lower unit seals.

NOTE:
For disposal of used oil consult your Powerte-
cOutBoards
dealer.
5.With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into
the gear oil drain screw hole.
Recommended gear oil:
Hypoid gear oil SAE#90

Gear oil quantity:

430.0 cm3 (14.54 US oz) (15.17

Imp.oz)

CAUTION

WARNING

Maitenance

«
...
57
58
59
60
61
...
»

Summary of Contents for 40Hp





































































Reviews:

No comments

Related manuals for 40Hp

Brand: Biostar Pages: 53

Brand: Safran Pages: 26

Brand: Digital Equipment Pages: 98

Brand: Gigabyte Pages: 8

Brand: MSI Pages: 112

Brand: ST Pages: 77

Brand: AOpen Pages: 8

Brand: National Semiconductor Pages: 13

Brand: Intel Pages: 92

WAFER-BW-N4-R10

Brand: IEI Technology Pages: 136

Brand: Acorp Pages: 74

Brand: EPOX Pages: 83

Brand: Fujitsu Pages: 22

Brand: Fujitsu Pages: 23

Brand: Fujitsu Pages: 28

Brand: Fujitsu Pages: 39

Brand: Fujitsu Pages: 44

CREMSON MODULAR STARTERKIT

Brand: Fujitsu Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands