air gun temperature up button
preheating station temperature up button
Figure3
air gun temperature up button
preheating station temperature up button
WARNING
In view of could cause serious injuries of fire accidents,please strictly observe the following
1.Must be confirmed well-connected handle and the machine, after that open the power supply
switch, all the parts removal or installed, must be turn off the power supply switch, then operate it
(High-Pressure is dangerous!)
2.When the power supply is turned, the air gun or soldering iron outlet temperature higher than 100
to 480 degrees Celsius (212-896 degrees Fahrenheit),the preheat plate surface temperature of
50-400 degrees Celsius(122-752 degrees Fahrenheit):DO NOT touch the air gun or soldering iron
metal part and preheat plate near the chassis,aluminum mesh,to replace nozzles or the tips and the
tips and other parts,should turn off the power supply and cooling to room temperature,then operate
it(Hihg-temperaturn is risk!)
3.DO NOT use the machine near flammable things(Fire hazard is dangerous!)
Terms
of
Use
1.Please ensure the Hot’s outlet is clear, must free from any blockages or obstructions.
2.After the work is completed , the air gun handle pot the frame or turn off air gun switch, the
machine automatically cooled to display“---”stop the air,then turn off the whole device power switch
in the back of the chassis.
3.When using the machine standard three nozzles:big,middle,small nozzles other than the smaller
nozzle,must separate air volume was djusted to the maximum use of a lower temperature and in a
short use.Avoid prolonged use of the damage to the air gun.
4.In regards to the usage requirements,choose the appropriate Hot air flow,different Hot air flow will
cause the temperature to be slightly different,and please maintain the distance between the oulet
and the object must be at least 2 mm.
5.When the iron is used for the first time,please pay attention to check the iron tip warming condition,
when the tip can melt the tin wire,please plate some tini on tip,then adjust to the desired temperature.
6.The tip temperature should not be too high,too high temperature would weaken the tip function.
when interval using ,can lowering the temperature.
7.Should be regularly use clean sponge to clear soldering tip, after finish use ,should wipe clean
soldering iron tip,plate new tin to prevent soldering iron tip oxide.
8.Preheat plate non-turn on the water structure, therefore, do not install the storage and use of
contact with oil,water,and plastic pellets to prevent leakage and other security risks.
9.The preheat plate should avoid being forced to tap or hard objects collided causing tiles fracture,
alloy resistance wire exposed affect the operating life.
10.The preheat plate DO NOT for prolonged use,and prevent chassis overheating.
Special Instructions:
Dear User! Our air gun and soldering iron handle adopt high strength stainless steel tube, the
machine must be inspected or calibrated four times in normal working condition during the
production process,the copper tube could be slight yellowing due to high temperature!When use
the new machine first time, it is normal that the steel tube at tube at a slight yellowing, please be
assured!
Preheating station
Temperature Range
Temperature Stability
Display Type
Area
Hot Air Reworks
Airflow type
Air Flow
Temperature Range
Temperature Stability
Display Type
Handle cable length
Soldering Iron
Temperature Range
Temperature Stability
Tip of ground voltage
Tip ground impedance
Display Type
Handle cable length
Performance comparison table
Model
Function
Functional components Preheating station
Preheating station
+Hot air reworks
Preheating station
+Hot air
Soldering station
Display type LED LED LED
Fahrenheit/Celsius
Conversion NO YES YES
NO YES YES
Temperature correction
YES YES YES
High temperature protection
Gun Type --- Brushless fan Brushless fan
Control Temperature way Digital PID Digital PID Digital PID
Operationg
1.Preheating station part
A.853A
1).Preheating station laid out plugged
2).Move bracket card board will need to preheat the element is placed above the plate move tighten the four screws on the
bracket,tiexed need tto preheat components
