background image

 

POWX1195 

EN

 

Copyright © 2016 VARO NV 

P a g e

 | 

7

 

www.varo.com 

8  OPERATION 

8.1 

Switching ON/OFF 

 

Switching on: 

 Press the operating switch (8). 

 

Switching off: 

 Release the operating switch(8) 

8.2 

Handle attachment (Fig. 2) 

For reasons of safety, only use the hammer drill with handle attachment. 
You will be able to obtain a safe body position when working by rotating the handle attachment. 
Loosen and turn the handle attachment in an ant-clockwise direction. Slip loop onto the neck 
of the housing tool and position the handle, then tighten the handle attachment. 

8.3 

Dust collection device (Fig. 3) 

Before  carrying  out  hammer-drilling  work  vertically  overhead  pull  dust  collecting  device  over 
the drill bit. 

8.4 

Hammer / drill switch 

 

The hammer/drill switch can switch the drill, hammer and hammer/ drill functions.  

 

To set the function, please use below compounding of front and rear hammer/drill switch. 

Important! When hammer drilling you will require a low pressure. Too much 
pressure  will  place  unnecessary  load  on  the  motor.  Check  the  drill  bits 
regularly. Re-sharpen or replace blunt drill bits. 

Do  not  use  the  chuck  with  SDS  connector  in  combination  with  the 
hammer/hammer drill function! 

 

Hammer/ drill mode: 

Drill in masonry, concrete and natural stone.  
Don’t use the hammer drill function for ceramic 
tile or others material can not withstand impact 
energy. 

 

Hammer mode:  

Drill in masonry, concrete and natural stone.  

 

Drilling mode:  

Drilling in wood, synthetic materials and metal. 

 

WARNING! No function mode:  

The  motor  turns  without  load, 
the  shaft  will  not  turn.    Do  not 
set  the  switch  like  this.  It  may 
damage the motor greatly. 

Summary of Contents for POWX1195












Reviews: