Powerplus POWX0057 Manual Download Page 6

 

POWX0057 

EN

 

Copyright © 2015 VARO 

P a g e

 | 

6

 

www.varo.com 

 

If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek 
medical help. Liquid ejected from the battery may cause irritation or burns. 

5.6 

Service 

 

Your power tool should be serviced by a qualified specialist using only standard spare 
parts. This will ensure that it meets the required safety standards. 

6  ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND 

CHARGERS 

6.1 

Batteries 

 

Never attempt to open for any reason. 

 

Do not store in locations where the temperature may exceed 40 °C. 

 

Charge only at ambient temperatures between 4 °C and 40 °C. 

 

Charge only using the charger provided with the tool. 

 

When disposing of batteries, follow the instructions given in the section “Protecting the 
environment”. 

 

Do not cause short circuits. If connection is made between the positive (+) and negative (-) 
terminal directly or via accidental contact with metallic objects, the battery is short circuited 
and an intense current will flow causing heat generation which may lead to casing rupture 
or fire. 

 

Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators 
and other polymer components may be damaged resulting in electrolyte leakage and/or 
internal short circuiting leading to heat generation causing rupture or file. Moreover do not 
dispose of the batteries in fire, explosion and/or intense burning may result. 

 

Under extreme conditions, battery leakage may occur. When you notice liquid on the 
battery, proceed as follows: 

- Carefully wipe the liquid off using a cloth. Avoid skin contact. 
- In case of skin or eye contact, follow the instructions below: 

 

Immediately rinse with water. Neutralize with a mild acid such as lemon 
juice or vinegar. 

 

In case of eye contact, rinse abundantly with clean water for at least 10 
minutes. Consult a physician. 

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do 
not incinerate the battery. 

6.2 

Charger 

 

Use the charger provided with the tool only to charge the battery 

 

Never attempt to charge non-rechargeable batteries. 

 

Have defective cords replaced immediately. 

 

Do not expose to water. 

 

Do not open the charger. 

 

Do not probe the charger. 

 

The charger is intended for indoor use only.  

Summary of Contents for POWX0057















Reviews: