background image

 

 

www.powermaxfitness.net 

Step 5 (only for multifunction)  
Functional Frame 

Use two M8*65 screws to fix the 
functional frame on the top and bottom  
U tube. 
 

Step 6 (only for multifunction)

 

 

Massage  
1.

 

First, screw off the three M8*16 screws  
below the massage machine head, (include 
flat washers and spring washers), and then  
place the massage machine head on the  
functional frame, and tighten up with the  
above unloaded screws.  

 

4.

 

EXERCISE ADVICES AND POLICY

 

Warm-up 

Take warm-up exercise for 5 to 10 minutes before using this machine each time. 

Breathing 

When exercising, you can’t hold your breath, usually inhale with nose when intending to release 
actions, and exhale with mouth. Inhaling should be coordinated with exhaling. If breathing too 
fast, you should stop exercising immediately. 

Frequency 

After the exercise of the same parts of the muscles, this part should have 48 hours’ rest. That is 
to say, it only can be exercised every other day. 

Load 

Decide the training volume based on the training state of everyone’s physical fitness, and then 
exercise according to the progressive overload principle. At the first exercising stage, muscles 
soreness is normal and can be eliminated by keep exercising. 

Diet  

To protect digestive system, exercise should be taken one hour after a meal. Eating should be 
done at least half an hour after exercising. When exercising, drink less water, and especially avoid 
drinking much so as not to increase the burden of heart and kidney. 

 

Summary of Contents for TDM-101

















Reviews: