Powermatic 701 Operating Instructions And Parts Manual Download Page 6 | Manualshive

Page: 6 / 20

background image

6

Introduction

This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and
maintenance procedures for a Model 701 Deluxe Bench-top Mortiser. This manual contains instructions
on installation, safety precautions, general operating procedures, maintenance instructions and parts
breakdown. This machine has been designed and constructed to provide years of trouble free operation if
used in accordance to instructions set forth in this manual. If there are any questions or comments,
please contact either your local supplier or Walter Meier. Walter Meier can also be reached at our web
site: www.waltermeier.com.

Specifications

Model No. ............................................................................................................................................ 701
Stock No. .....................................................................................................................................1791310
Chisel shank capacity, maximum ......................................................................................................... 3/4"
Chuck capacity, maximum ................................................................................................................... 1/2"
Chisel stroke, maximum.................................................................................................................... 5-1/2"
Chisel center to fence distance ......................................................................................................... 4-3/8"
Bushing sizes provided ................................................................................................................ 5/8",  3/4"
Fence size ......................................................................................................................... 12-1/2"  x  2-5/8"
Base size ...................................................................................................................... 16-5/16" x 13-3/4"
Capacity under hold-down ...................................................................................................................... 5"
Spindle speed............................................................................................................................ 1725 RPM
Motor (TEFC) ....................................................................... 3/4 HP, 1 PH, 4P, 115V/230, Pre-wired 115V
Weight (net/shipping) ................................................................................................................. 93  /  100 lb

The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier reserves the right to change specifications at any time and without
prior notice, without incurring obligations.

«
...
4
5
6
7
8
...
»

Summary of Contents for 701





















Reviews:

No comments

Related manuals for 701

Brand: Makita Pages: 12

Brand: Cal Flame Pages: 12

Brand: Fiesta Pages: 13

Brand: Master Forge Pages: 52

Brand: Grilla Pages: 16

Brand: Jamie Oliver Pages: 12

Brand: P.I.T. Pages: 21

18V CORDLESS HAMMER DRILL

Brand: Challenge Xtreme Pages: 21

Brand: Rebel Pages: 64

Brand: Skil Pages: 152

Brand: Napoleon Pages: 32

Flex Power 241-0436

Brand: Master-force Pages: 20

Brand: Hamrforge Pages: 8

Brand: Member's Mark Pages: 27

Brand: AEI Pages: 27

Brand: Hitachi Koki Pages: 112

Brand: Sparky Group Pages: 102

Brand: Black & Decker Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands