manualshive.com logo in svg

Powermatic 1632, Operating Instructions And Parts Manual

Share
Download
Powermatic 1632 Operating Instructions And Parts Manual Download Page 6

SPECIFICATIONS: 1632 Open-End Sander 
 

Working width (reversing stock) ....................................................................................................................... 16" (32") 
Working thickness...................................................................................................................................................... 5" 
Minimum board length.........................................................................................................................................13-3/4" 
Head configuration ......................................................................................................................................combination 
Feed motor (1632-3) ..................................................................................................................................1/4 HP, 3 Ph 
Feed motor (1632-1) .................................................................................................................................. 1/4 Hp, 1 Ph 
Feed speeds (variable FPM) .............................................................................................................................. 15/32.5 
Sanding belt dimensions .......................................................................................................................... 17" W x 54" L 
Sanding belt speed (SFPM) .................................................................................................................................. 2,200 
Compressed air requirements at 5 atm (PSI)................................................................................................................4 
Dust collection minimum CFM required.................................................................................................................... 800 
Dust port diameter...................................................................................................................................................... 4" 
Overall dimensions ......................................................................................................................40" L x 29" W x 66" H 
Main motor (1632-3)..................................................................................... 7-1/2 HP, 3 Ph, 230/460V (prewired 230V) 
Main motor (1632-1).................................................................................................................... 5 HP, 1 Ph, 230V only 
Net weight ......................................................................................................................................................... 996 lbs. 
Shipping weight...............................................................................................................................................1,106 lbs. 
 
 
 
 
 
 
 
NOTE:  The above specifications were current at the time this manual was published, but because of our policy of 
continuous improvement, WMH Tool Group reserves the right to change specifications without notice and without 
incurring obligations. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

Summary of Contents for 1632





























Reviews:

No comments

Brands by name

Popular brands

Load more brands