manualshive.com logo in svg

Powermatic 1285, Operating Instructions And Parts Manual

Share
Download
Powermatic 1285 Operating Instructions And Parts Manual Download Page 7

 

7 

Introduction 

This manual is provided by Powermatic covering the safe operation and maintenance procedures for a 
Model 1285 Jointer. This manual contains instructions on installation, safety precautions, general 
operating procedures, maintenance instructions and parts breakdown. This machine has been designed 
and constructed to provide years of trouble free operation if used in accordance with instructions set forth 
in this manual. If there are any questions or comments, please contact either your local supplier or WMH 
Tool Group. WMH Tool Group can also be reached at our web site: www.wmhtoolgroup.com. 

 

Specifications 

 

Model Number ................................................................................................................................... 1285 
Stock Number (3HP, 1Ph, 230V, with standard cutterhead).......................................................... 1791241 
Stock Number (3HP, 3Ph, 230V/460V*, with standard cutterhead) ............................................... 1791249 
Stock Number (3HP, 1Ph, 230V, with helical cutterhead) ............................................................. 1791307 
Stock Number (3HP, 3Ph, 230V/460V*, with helical cutterhead) ................................................... 1791308 
Cutting Capacity (W x D) (in.).................................................................................................. 11-3/4 x 3/4 
Cutterhead Speed (RPM).................................................................................................................. 5,000 
Rabbeting Capacity (in.)........................................................................................................................ 3/4 
Table Surface (L x W) (in.) ............................................................................................................. 84 x 12 
Outfeed Table Height from Floor (in.) ............................................................................................... 31-5/8 
Fence Size (L x W) (in.) ....................................................................................................... 47-1/4 x 5-1/4 
Fence Tilt (degrees)...................................................................................................... 90, 45 right, 45 left 
Fence Positive Stops (deg.) ....................................................................................................... 45 and 90 
Number of Knives – standard cutterhead ................................................................................................. 3 
Number of Inserts – helical cutterhead ........................................................................ 44, with 2 rabbeting 
Size of knives – standard cutterhead (L x W x T) (in.)........................................................ 12 x 13/16 x 1/8 
Dust Collection Minimum CFM Required.............................................................................................. 800 
Approximate Net Weight (lbs.) ............................................................................................................. 762 
Approximate Shipping Weight (lbs.) ..................................................................................................... 880 
 
*pre-wired 230V  
 
 

 

The above specifications were current at the time this manual was published, but because of our policy of 
continuous improvement, WMH Tool Group reserves the right to change specifications at any time and 
without prior notice, without incurring obligations. 

 
 

Summary of Contents for 1285













































Reviews:

No comments

Brands by name

Popular brands

Load more brands