Powermate PMC601200 Owner'S Manual Download Page 4

TOOLS  REQUIRED:  

Hammer, 1/2” wrench, ratchet with a 1/2” socket, and wood blocks.

Refer to the drawing for proper alignment of Foot bracket and Wheel brackets.

Refer to the parts list on pages 15 and 16.

Wheel Bracket & Wheel  Installation

1. 

Block up end of generator, about 8” high, opposite the fuel tank cap to install wheels and wheel bracket assy.

2.

Add 5/16 washer 

(item 29)

to the 1 3/4” bolts 

(item 71)

and insert bolts/washers through the holes located in the base pan of 

the carrier.

3.

Place the wheel bracket 

(item 65)

through the bolts and add a 5/16 nyloc nut 

(item 27)

and tighten securely. (On the bottom 

side of the pan in-between the holes will be a 1” square brace, the wheel bracket will set on this brace).  

4.

Add wheel spacer 

(item 70)

to the axle.

5.

Slide the wheel 

(item 64)

onto the axle until it is snug against the spacer.  The wheel is on correctly if there is approximately a

1/2” gap between the carrier tubing and the side of the wheel.  If it is less then 1/2” from the carrier, turn the wheel over and 
reinstall.  Align the wheels parallel to the carrier tubing and tighten nuts securly.  To align correctly, the bolts holding the wheel
bracket may have to be loosened.

6.

With a hammer, add the plastic cap 

(item 69)

on end of axle.

7.

Repeat above instructions for the remaining wheel.

Foot bracket Installation

1.

Block up opposite end of the unit, about 8” high.

2.

Add 5/16 washer 

(item 29)

to 1” bolts 

(item 30)

and place through holes in the base pan.

3.

Add foot bracket assembly 

(item 66)

to bolts, add 5/16 nyloc nuts 

(item 27)

and tighten securely.

4. 

Add support bracket 

(item 68)

from foot bracket to the base pan.  Secure in place with 1” bolts 

(item 30)

, washers 

(item 29)

and 5/16 nyloc nuts 

(item 27)

.

Locking Handle

1.

Attach the lanyards 

(item 72)

to the release 

pins 

(item 73) 

and carrier as shown in the 

illustration.

2.

To lock the handle in the extended position, 
align the holes in the handle brackets with the 
holes in the carrier brackets and insert the 
release pins.

PORTABILITY KIT INSTALLATION

1

2

4

English

72

73

Summary of Contents for PMC601200

















Reviews: