background image

Read these instructions thoroughly before starting installation. For easier assembly, we suggest 
you run all wires prior to mounting your Pod speakers. 

1.  Determine where the Pod will be placed on the tower bar and a what angle the speaker will be mounted. 

Using one of the rubber inserts mark the bar with a felt-tip pen. This will be where the speaker wire 
comes through the bar and to the Pod.

        

NOTE: This first step is VERY important. Make sure of the exact location and orientation you         

        want BEFORE drilling any holes.

2.  Drill a 0.25 to 0.5-inch hole for the speaker wire on the mark made on the tower bar. De-burr the hole to 

keep from damaging the wire’s insulation and causing a short. It is a good idea to treat the hole to inhibit 
corrosion.

3.  Remove the Allen Screws securing the Aluminum Top Bracket to the Aluminum Base.
4.  Using the Safety Cable hang the Pod on the tower bar near its eventual mounting location.
5.  Run minimum of 16-gauge speaker wire (not included) through the tower bar and leave 8”  

to 12” of the wire hanging out of the hole you previously drilled. Select one of the rubber inserts  
(if necessary) and run the speaker wire through the hole in the insert.

6.  Connect the speaker wire coming out of the tower bar to the speaker wire coming out of the Pod. Note the 

polarity (the black wire from the Pod is negative –) See Fig. 3

7.  Hold the Pod and place the Aluminum Base flush with the tower bar. Be sure to push any excess speaker 

wire back into the tower bar. Make sure the speaker hole from the Aluminum Base of the Pod (or insert) is 
aligned with the hole in the tower bar—use caution not to pinch the wire.

8.  Affix the Aluminum Top Bracket over the tower bar and screw in the two Allen Head bolts at first by hand. 

Next using the supplied Allen wrench tighten the bolts evenly. When fully tightened the Pod should not 
move.

9.  Connect the other end of the speaker wire to the amplifier following the instructions supplied with the 

amplifier. Be sure to observe proper polarity of the speaker wire when connecting to the amplifier.

1/2”

Fig.3
The speaker wire from the Pod
with black is the negative lead

7

Summary of Contents for XL-POD65













Reviews: