background image

POWERBASS AUTOSOUND LIMITED WARRANTY POLICY

PowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms:

PowerBass Autosound Speakers are to be free of defects in material and workmanship for a period 
of one (1) year.

This warranty applies only to PowerBass products sold to consumers by Authorized PowerBass Dealers in the 
United States of America.  Products purchased by consumers from a PowerBass dealer in another country are 
covered only by that country’s Distributor and not by PowerBass USA.

This warranty covers only the original purchaser of PowerBass product.  In order to receive service, the purchaser 
must provide PowerBass with the receipt stating the consumer name, dealer, product and date of purchase.

Products found to be defective during the warranty period will be repaired or replaced (with a product deemed 
to be equivalent) at PowerBass’s discretion and will not be liable for incidental or consequential damages. 
PowerBass will not warranty this product under the following situations:

 

• Amplifiers received with apparent rust or corrosion

 

• Any evidence of liquid damage or exposure to excessive heat

 

• Abuse such as holes in the cone, surround or ripped spider

 

• Voice coil damage due to amplifier clipping or distortion

 

• Product that has not been installed according to this owners manual

Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the 
period of the express warranty set forth above.  Some states do not allow limitations on the length of an implied 
warranty, so this limitation may not apply.  No person is authorized to assume for PowerBass any other liability in 
connection with the sale of this product.

Please call (909) 923-3868 for PowerBass Customer Service.

  You must obtain an RA# (Return Authorization 

Number) to return any product to PowerBass. 

The RA number must be prominently marked on the outside 

of the shipping carton or the delivery will be refused.

  Please pack your return carefully; we are not 

responsible for items damaged in shipping.  Return the defective product along with a copy of the original dated 
retail sales receipt, plus $12.00 for handling and diagnostic evaluation to:

PowerBass USA, Inc., Attn: Returns (RA#__________)
2133 S. Green Privado, Ontario, CA 91761

Residents of HI, AK and US territories will be charged for return shipping.  All inquires regarding service and 
warranty should be sent to the above address.

NOTE: Return only the part(s) that must be repaired or replaced. Do not send the entire system! It 
will only cause unnecessary delays and may result in damage that is not covered by this warranty.

Summary of Contents for PS-AWB101T





















Reviews: