background image

M9780pr-0920

3

WARNINGS AND CAUTIONS

B

M9780pr-0920

• In the unassembled state, this package contains small parts. Adult assembly is required.
• Use the charger in dry locations only.

ELECTRICAL HAZARD

CAUTION

• Battery can fall out and injure a child if vehicle tips over. Always use battery retainer.
• 

PREVENT FIRE

 -  

Never modify the electrical system. Alterations could cause a fire resulting in serious injury 
and could also ruin the electrical system.

 -  

Use of the wrong type battery or charger could cause a fire or explosion resulting in 
serious injury.

 -  

 Use of Power Wheels

®

 components in products other than Power Wheels

®

 vehicles could 

cause overheating, fire or explosion.

•  The battery must be handled by adults only. The battery is heavy and contains sulfuric acid 

(electrolyte). Dropping the battery could result in serious injury.

• Never allow children to charge the battery. Battery charging must be done by adults only.

A child could be injured by the electricity involved in charging the battery.

• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage each time 

you charge the battery. If damage or excessive wear is detected, do not use the charger or the 
battery until you have replaced the worn or damaged part.

• 

HOT

 motors. Handle carefully. 

WARNING

• 

Prevent Injuries and Deaths

    • Direct Adult Supervision Required
    • Never Ride at Night.
   •  

Keep Children Within Safe Riding Areas. 

      These areas must be:
   

- away from swimming pools and other bodies of water to prevent drownings     

   

- generally level to prevent tipovers

   

- away from steps, steep inclines, cars, roads and alleys.

   • Riding Rules
      Make sure children know and follow these rules for safe driving and riding.
   

- Always sit on the seat.

   

- Always wear shoes.

   

- Only 2 (two) riders at a time.

WARNING

 RIDING HAZARD

Summary of Contents for M9780 Cadillac ESCALADE Custom Edition





































Reviews: