Power Wheels GT Racer Kart Owner'S Manual With Assembly Instructions Download Page 7

CAUTION

Use the charger in dry locations only.

WARNING

7

About Thermal  Fuses

Your Power Wheels

®

12 volt battery is equipped with a

built-in thermal fuse. The thermal fuse is a self-resetting
safety device which automatically “trips” and shuts down
operation of the vehicle if the vehicle is overloaded or the
driving conditions too severe. Once a fuse has “tripped”, 
it will automatically reset itself after approximately 
25 seconds and allow the vehicle to resume normal
operations. To avoid repeated automatic shutdowns, 
do not overload the vehicle by exceeding the 120 lb.
(54.4 kg). maximum weight capacity or by towing 
anything behind the vehicle. Avoid severe driving
conditions, such as driving up very steep slopes or
running into fixed objects, which can cause the wheels 
to stop spinning while power is still being supplied to
the motors.

If a thermal fuse in a battery continually trips under
normal driving conditions, please contact your local 
Power Wheels

®

Authorized Service Center. For the

location of the Authorized Service Center nearest to 
you, please visit us on-line at www.powerwheels.com
or call 1-800-348-0751.

Important Notes

• Your new battery must be charged for at least 18 hours

before you use it in your vehicle for the first time.

• You do not need to remove the battery from your 

vehicle to recharge it.

• The battery must be upright while charging.

• The charger is not a toy.

• Do not short circuit the battery.

• We recommend that you start charging your battery

before beginning assembly of your new vehicle.

• Before charging the battery, examine the battery case 

for cracks and other damage which may cause sulfuric 
acid (electrolyte) to leak during the charging process.
If damage is detected, do not charge the battery or 
use it in your vehicle. Battery acid is very corrosive and 
can cause severe damage to surfaces it contacts.

• Do not charge the battery on a surface which could be

damaged by the acid contained inside the battery. Take
precautions to protect the surface on which you charge
your battery.

• Use only a Power Wheels

®

12 volt charger with type

12V connector (120 VAC 60 Hz 28W with an output of
12 VDC 1200mA) to charge your Power Wheels

®

rechargeable 12 volt battery.

• If your battery is old and will not accept a charge, do not

leave it in the vehicle. Always remove a dead battery
from the vehicle.

• Battery can fall out and injure a 

child if vehicle tips over. Always use
battery cover (clamp).

• PREVENT FIRE

- Never modify the electrical system.

Alterations could cause a fire resulting
in serious injury and could also ruin the 
electrical system.

- Use of the wrong type battery or 

charger could cause a fire or explosion
resulting in serious injury.

- Use of Power Wheels

®

components in

products other than Power Wheels

®

vehicles could cause overheating, 
fire or explosion.

• The battery must be handled by adults

only. The battery is heavy and contains
sulfuric acid (electrolyte). Dropping the
battery could result in serious injury.

• Never allow children to charge the battery.

Battery charging must be done by adults
only. A child could be injured by the 
electricity involved in charging the battery.

• Never lift or carry the battery by the wires

or connector. This can damage the battery
and possibly cause a fire resulting in 
serious injury. Lift and carry the battery 
by the case only.

• Read the safety instructions on 

the battery.

• Examine the battery, charger and their

connectors for excessive wear or damage
each time you charge the battery. If
damage or excessive wear is detected, do
not use the charger or the battery until you
have replaced the worn or damaged part.

ELECTRICAL HAZARD

Battery Charging

E

Summary of Contents for GT Racer Kart

























Reviews: