Power-Tronics XR5B-400 Manual Download Page 16 | Manualshive

Page: 16 / 21

background image

© 2018 Power-Tronics, Inc.

16

Conversion From Older Shunt-Wound Voltage

Regulation to Modern Solid-State Voltage Regulation

It is possible to use the XR5B-400 Universal Voltage regulator with older Shunt-Wound
exciters that originally had manual or mechanical voltage regulators by converting the
wiring as in the diagrams below. If the generator will not build up after conversion, try
switching your F+ and F- leads at the regulator and try starting up again.

NOTE:

Armature brushes

MUST BE ISOLATED

from the field leads for
proper operation!

«
...
14
15
16
17
18
...
»

Summary of Contents for XR5B-400






















Reviews:

No comments

Related manuals for XR5B-400

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: U-Prox Pages: 31

Brand: Abus Pages: 12

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: QUNDIS Pages: 2

Brand: WAM Pages: 62

Brand: walimex Pages: 7

Brand: Walchem Pages: 2

Brand: Walchem Pages: 73

Brand: Walchem Pages: 126

Brand: wallas Pages: 2

Brand: FEAS Pages: 4

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

Brand: HQ Power Pages: 23

Brand: Auber Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands