background image

8

P

R

ODUCT  WA

RR

ANTY

Power-Tronics, Inc.

assumes no liability for damages due to incorrect voltage or other voltage

related damages resulting from either output of the generator or input to the generator exciter

system.  These problems should be protected with external devices provided by the customer

such as

 fuses, surge suppressors, over/under voltage and frequency controls.

Power-Tronics, Inc.

warranties 

only parts and workmanship

 of this product for 

a period of

1 year from the original date of purchase from Power-Tronics, Inc. 

  Under warranty,

Power-Tronics, Inc. will replace, exchange or repair the defective product 

without labor or

parts cost to the customer.

  Remaining warranty of the original product will be transferred to

the replaced or repaired product.  To obtain warranty, a copy of the original purchase receipt

must be sent in with the defective product, which clearly shows the purchase date and serial

number of the defective part.  A repair request form must be sent in with the product before

repairs will begin.  You can obtain this form through contacting Power-Tronics, Inc..  Send

repairs to:  Power-Tronics, Inc., 2802 Cobbler Ln., Kerrville Texas USA 78028.  Send in

repairs only by UPS or FedEx.

Any one of the following conditions will void the warranty:

v

 

Overheating of the power supply resistor on the printed circuit card.

v

 

Ove

rheating of the SCR or freewheeling diode.

v

 

Physical damage to the printed circuit card, housing or components.

v

 

Unauthorized repair or alteration of printed circuit card.

v

 

Conductive or corrosive contamination of the circuit card.

v

 

Removal of our company identification from the product.

v

 

Removal of any conformal coating of the printed circuit card or components.

v

 

Overheating of foil on the printed circuit card.

v

 

Inappropriate or infeasible application

v

 

Use on any external device other than manufactured by Power-Tronics, Inc.

No other warranty is expressed or implied.

Summary of Contents for VR758









Reviews: