manualshive.com logo in svg

Power Probe IV, User Manual

Share
Download
Power Probe IV User Manual Download Page 24

Power Probe IV

www.powerprobe.com   ·   800-655-3585

Product Specifications 

Specs

Min Operating Voltage …………………………........ 8 VDC
Max Operating Voltage …………………………....... 30 VDC
Max Tip Voltage ……………………………………...... 450 Volts 
Probe Tip Resistance to Ground ………………....... 130K Ohms
Computer Safe ……………………………………......... 0.1mA floating tip
Voltage Measurement ……………………………....... -100 to 200 VDC / VAC (70 VAC RMS)
Voltage Resolution ................................................ -99.99 to 99.9 V – 0.01V (10mV)

100.0 to 199.9 V – 0.1V (100mV)

Glitch Capture ....................................................... >380µS Min Pulse Width
Power Feed Test ..................................................... < 30 mA
Resistance Measurement ...................................... 0.1 Ohms to 10K Ohms
Frequency Measurement ...................................... 1Hz to 9999Hz
Driver Test .............................................................. 50 Ohm Pull Up on Tip

Driver On Range: 50mV to 1V

ECT Signal Detection ............................................ 2 sec.
Fuel Injector Mode ................................................ LED Flash @ Min 35V @ 100µS Pulse
Red LED Response ................................................. Within 0.5V BATT V and < 10 Ohms
Green LED Response ............................................ < 10 Ohms
Circuit Breaker ....................................................... 8 Amp Thermal – Auto Reset
Breaker Trip Response ........................................... 8 Amps = No Trip

10 Amps = 20 min.
15 Amps = 6 sec.
25 Amps = 2 sec.
Short Circuit = 0.3 sec.

Operating Temperature ........................................ -20°C (-4°F) to 50°C (122°F)
Storage Temperature ............................................. -40°C (-40°F) to 65°C (149°F)

Page 22

Summary of Contents for IV





























Reviews:

No comments

Brands by name

Popular brands

Load more brands