To activate your warranty or find a Power-Pole Certified
Warranty Center, go to
www.power-pole.com
2
Need help? Contact our Technical Support Team at
1 + 813.689.9932 Option 2
9010 Palm River Road, Tampa, Florida 33619
phone 813.689.9932 fax 813.689.8883 • power-pole.com
©2019 all rights reserved. Power-Pole Shallow Water Anchor U.S. Patent No. 6,041,730
General Statement (for all devices)
Warning: Changes or modifications to this device not expressly approved by JL Marine Systems, Inc. could void the user’s authority to operate the equipment.
FCC Specific Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, he user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Part 15.19 Warning Statement –
(Required for all Part 15 devices) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC/ISED RF Exposure
ENGLISH: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of
the user under normal operating conditions. The transmitter must not be co-located or operating in conjuction with any other antenna or transmitter.
FRENCH: Cet équipment est conforme aux limites d’exposition aux radiations dans un environment non controle. Cet équipment est en contact direct avec le
corps de l’utilisateur dans des conditions de fonctionnement normales. Cet émetteur ne doit pas être co-localisées ou opérant en conjunction avec tout autre
antenne ou transmetteur.
ENGLISH: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must not accept any interference, including interference that may cause undesired operation of the device.
FRENCH: Le présent est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de license. L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
C-MONSTER 2.0 CONTROLLER
INSTRUCTIONS
WIRELESS
FOOT SWITCHES
WIRELESS
DASH SWITCH
REMOTE CONTROL
KEY FOB
Battery Replacement
(Dash Switch )
IMPORTANT:
Make sure battery replacement is done in a dry
location.
STEP 1:
Remove the (
2
) screws using a Phillips-Head screwdriver.
STEP 2:
Remove
Dash Switch Cover
using a Flat-Tip Screwdriver.
FIG. 1
STEP 3:
Remove
Switch Membrane
and
Circuit Board
from the
base.
FIG. 2
STEP 4:
Remove battery from holder and replace with a CR2032 3v
Lithium Coin Battery.
STEP 5:
Reassemble Dash Switch. Make sure
Switch Membrane
is seated properly.
Dash Switch Cover
Figure 1
Screw Locations
Figure 2
Circuit Board
Membrane
C-Monster 2.0 Controllers
Battery Replacement
(Key Fob)
IMPORTANT:
Make sure battery replacement is done
in a dry location.
STEP 1:
Remove
Key Fob Cover
using a
Flat-Tip
screwdriver.
FIG 1
STEP 2:
Remove
Switch Membrane
and
Circuit
Board
from the base
FIG 2
STEP 3:
Remove battery from holder and replace
with a CR2032 3v Lithium Coin Battery.
STEP 4:
Reassemble Key Fob. Make sure
Switch
Membrane
is seated properly.
Figure 1
Key Fob
Cover
Figure 2
Circuit Board
Figure 3
Membrane
