background image

 

POWXG2061 

EN

 

Copyright © 2017 VARO 

P a g e

 | 

3

 

www.varo.com 

LONG REACH HEDGE TRIMMER 25.4CC 
POWXG2061 

1  APPLICATION 

The hedge trimmer should only be used for trimming hedges, bushes and shrubs. Other use of 
the trimmer, not included in this manual, could damage the trimmer or seriously injure the 
operator and is therefore expressively excluded from the application range. 

WARNING!  Read  this  manual  and  general  safety  instructions  carefully 
before  using  the  appliance,  for  your  own  safety.  Your  tool  should  only  be 
passed on together with these instructions. 

2  DESCRIPTION (FIG. A) 

1. 

Front drive shaft tube 

2. 

Lock pin 

3. 

Lock knob 

4. 

Connector 

5. 

Barrier 

6. 

Front handle 

7. 

Rear drive shaft tube 

8. 

Engine switch 

9. 

Throttle lock 

10.  Throttle trigger lockout 
11.  Auxiliary handle 
12.  Suspension ring 
13.  Output flange 
14.  Spark plug 
15.  Engine 

16.  Starter handle 
17.  Fuel tank 
18.  Choke knob 
19.  Primer bulb 
20.  Filter cover 
21.  Throttle trigger 
22.  Blade cover 
23.  Cutting blade 
24.  Grease nozzle 
25.  Transmission 
26.  Locking lever 
27.  Grip 
28.  Safety lever 
29.  Gear box  

3  PACKAGE CONTENT LIST 

 

Remove all packing materials. 

 

Remove remaining packaging and transit supports (if existing). 

 

Check the completeness of the packing content. 

 

Check the appliance, the power cord, the power plug and all accessories for transportation 
damages. 

 

Keep the packaging materials as far as possible till the end of the warranty period. 
Dispose it into your local waste disposal system afterwards. 

WARNING:  Packing  materials  are  no  toys!  Children  must  not  play  with 
plastic bags!  Danger of suffocation! 

Long reach hedge trimmer 25.4 cc 
Safety blade cover  
Carrying belt 
Manual 
Spark plug wrench 

Open-end wrench 8-10 mm 
2 x Torx wrench 25-30 
Screwdriver 
Mixing cup 

When parts are missing or damaged, please contact your dealer. 

Summary of Contents for POWXG2061

















Reviews: